) A business jet with a mass of about 13,000 kg when fully loaded with 9 passengers takes off at a speed of 240 km/h. Calculate the takeoff speed when the airplane has 4 empty seats. Assume each passenger with luggage is 150 kg and the wing and flap settings are maintained the same.

) A business jet with a mass of about 13,000 kg when fully loaded with 9 passengers takes off at a speed of 240 km/h. Calculate the takeoff speed when the airplane has 4 empty seats. Assume each passenger with luggage is 150 kg and the wing and flap settings are maintained the same.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

the takeoff speed of a military aircraft from an aircraft carrier is approximately 170 mi/hr relative to the air. They acquire this speed through a combination of a catapult system present on the aircraft carrier and the aircraft's jet propulsion system. A common strategy is to head the carrier and the plane into the wind. If a plane is taking off from an aircraft carrier which is moving at 50 mi/hr into a 30 mi/hr headwind, then what speed (in mi/s)relative to the deck of the aircraft carrier must it obtain to takeoff?
9.38 The drag coefficient for a newly designed hybrid car is predicted to be 0.21. The cross-sectional area of the car is 30 ft². Determine the aerodynamic drag on the car when it is driven through still air at 55 mph.
An airfoil of surface area 0.1 m² is tested for lift L in a wind tunnel. (Conditions can be considered as incompressible flow.) At an angle of attack of 5 °, with standard air density 1.22 kg/m³, at a speed of 30m/sec, the lift is measured to be 3.2 kgf. What is the lift coefficient? For a prototype wing of area 10 m², what is the approximate lift at an air speed of 160 kmph at the same angle of attack of 5 °?
I need the answer as soon as possible
The coefficients of friction between the load and the flat-bed trailer shown are 0.35 (static) and 0.30 (kinetic). Knowing that the speed of the rig is 72 km/h , determine the shortest distance in meter in which the rig can be brought to a stop if the load is not to shift.
If the distance between the tires is 2.6 m and the center of mass of the car is located 1 m above a horizontal ground. Determine the maximum constant speed that the car can travel without overturning. 90 kph а. 140 kph 180 kph d. 200 kph b. C. е. none of the above
The 1540-kg car has a velocity of 26 km/h up the 10-percent grade when the driver applies more power for 18 s to bring the car up to a speed of 67 km/h. Calculate the time average F of the total force tangent to the road exerted on the tires during the 18 s. Treat the car as a particle and neglect air resistance. | 10 100 Answer: F = i kN
8) The radius of the moon is roughly 1080 miles. The acceleration of gravity at the surface of the moon is about 0.165 where g, g is the acceleration of gravity at the sinface of the earth. Determine the velocity of escape for the moon. /172 miser
The drag of a small submarine hull is desired when it is moving far below the free surface of water. A 1/10scale model is to be tested. What dimensionless group should be duplicated between the model and prototype and why? If the drag of the prototype at 1 knot is desired, at what speed should model be moved to give the drag to be expected by the prototype? Would his result still be true if the prototype were to be moved close to the surface? Support your response with a model law and state any two example ?
A 900-kg car travelling east at 15.0 m/s collides with a 750-kg car travelling north at 20.0 m/s The cars stick together. Assume that any other unbalanced forces are negligible What is the change in momentum of the colliding bodies? What is the speed of the wreckage just after the collision? In what direction does the wreckage move just after the collision?
Calculate the average flow rate when transporting a liquid at 10 [m3 / h] using a 3in schedule number 40 standard steel pipe. If the specific gravity of the liquid is 0.9, what is the mass-based flow rate?
Problem 1. In deriving braking distance, we assume a constant acceleration/deceleration rate, a. In fact, AASHTO assumes constant acceleration a(t): = c (constant) in most of its design procedures. Although this is not entirely true, distances required for acceleration or deceleration can be realistic if appropriate values are chosen for the constant acceleration process. Linear acceleration a(t) = c₁t (t is time elapse and c₁ is jerk rate or rate of change) is a better approximation to the acceleration process. a) What is the practical stopping distance for a vehicle with initial speed 70 mph, if acceleration is described by a linear function of time using a(t) = -1.8t (t is time elapse in seconds). b) Use a constant acceleration rate to achieve the same stopping distance. What is this constant acceleration rate? Problem 2. A car hits a tree at an estimated speed of 25 mph on a 3 % upgrade. If skid marks of 120 ft are observed on dry pavement (coefficient of braking friction, fo…