A boat in rectangular shape has the following dimension: 5m long, 8m wide, and 5m deep. It is submerged at 3 meter draft initially. 9000kg was placed at the edge of the boat and caused the boat to tilt over and rolled a bit. Determine the TOTAL metacentric height MBo when it rolled on one side in meters.

A boat in rectangular shape has the following dimension: 5m long, 8m wide, and 5m deep. It is submerged at 3 meter draft initially. 9000kg was placed at the edge of the boat and caused the boat to tilt over and rolled a bit. Determine the TOTAL metacentric height MBo when it rolled on one side in meters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

12- the axial surface is vertical a- Horizontal normal b- Plunging normal c- Other
Also please I ndicate which members are in compression
Use force method or displacement method.
see picture for instructions. Use VIRUAL WORK METHOD Height is 3m.
Determine the force in members BC, CE, and EF. AMATHalino.com 1m 0.75 m E im Figure T-01 C 80 KN MATHalino.com 1m 50 kN
The difference in elevation between line AB is 6.5 m. A 100 meter steel tape was used with a standard pull of 12 kg under a temperature of 300C. The line was measured on a sloping ground and found to be 486.396 m. But during the measurement, the temperature was 220C and the tape was suspended under a pull of 14 kg. The tape weighs 5 kg and it was supported at 0-30-75-100 marks when measuring. Determine the correct slope distance and horizontal distance. A = 0.04 sq. cm
Answer using slope deflection method only, use the picture below as guide for the formulas. thanksShow your complete solution and draw fbd
2-4. A sharp-edged rectangular weir was used to measure the flow of water from a trombone cooler under conditions such that the Francis formula, q = C(L - 0.2H)1 %3D may be applied. cent. The value of L was 8.0 in. with an estimated precision of +0.1 in. H was measured to be 4.0 in., but because of turbulence the precision of this measurement was estimated to be only +0.4 in. (a) What is the "maximum possible systematic error" in the calculated value of q? (b) What is the probable precision of the calculated value of q? (c) Express the calculated value of q in the proper and accepted form. (d) If the weir is to be calibrated at these conditions by collecting and weighing the water which flows over the weir in a period of approximately min, with what precision should the individual measurements be made if the desired precision of q is +0.5 per cent? For q in cubic feet per second and L and H in feet, C 3.33 3 per
Solve the capacity of a 4.2-m steel column, pin-supported at both ends, having the cross section as shown. a.) Service axial compressive load capacity (ASD) 390 mm X Use Fy-350 MPa. O 11.557.992.5006 N O 10.402.193.2506 N O206,659.375,00 N O 6.920,953.5932 N 300 mm y: 55 mm 45 mm 45 mm
QL Find the Forces members BD, CD end CE in 200 N/m 10 1.5m 2n
(96 H.WE Draw S.fiD andd B.M.n for beam shown by graphial me thod? Ans/ Vome= 29.5 W 25 W /m Vime = Vnx = -25.5 W 12 W/m 1Smhinge 1-5m = 27.1 W.m 3m 1.5m 1.5m 2m 3m Monny = -51 W.m.
3. Determine the magnitude and location of the total hydrostatic force acting on the inclined plane AB Paia - IS KAA 0-70m OIL ( 6* 0.0) 1.Om WATER 1-20m GLYCE RINE (so - 1-26) 30 Alelie is presenting