A block(unit weight = 19.5 kN/m^3) 0.51m square and 331mm deep floats on a stratified liquid composed of a 200mm layer of water above a layer of mercury(s.g. = 13.6). If a downward force of 1200 N is applied to the center of mass of this block, what is the new position of the bottom of the block relative to the mercury surface in mm?. Write numerical value only and in 2 decimal places.

A block(unit weight = 19.5 kN/m^3) 0.51m square and 331mm deep floats on a stratified liquid composed of a 200mm layer of water above a layer of mercury(s.g. = 13.6). If a downward force of 1200 N is applied to the center of mass of this block, what is the new position of the bottom of the block relative to the mercury surface in mm?. Write numerical value only and in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum block (SG=2.5) has a dimension of 0.22 m x 0.22 m xh meters. It is floating in mercury (SG-13.6) and the submerged height of the block is 0.72 m. Determine the weight (kN) of the block.
Strength of materials som.
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
An aluminum block (SG=2.5) has a dimension of 0.29 m x 0.29 m x h meters. It is floating in mercury (SG=13.6) and the submerged height of the block is 0.85 m. Determine the weight (kN) of the block.
Solve correctly
III. PROBLEM SOLVING 36. To measure a base line, a steel tape 30 m long, standardised at 15° C with a pull of 80 N was used. Find the correction per tape length, if the temperature at the time of measurement is 25° C and the pull exerted is 150 N. Take Young's modulus E = 2 × 10^5 N/mm2 and coefficient of thermal expansion a = 11.2 × 10^6/°C. Cross-sectional area of tape is 8 mm2.
The surface tension of mercury at 60°C is 0.47N/m. What capillary height in mm will occur in this fluid whe in contact with a glass tube of radius 0.3mm? Use 130° for mercury. O 11.5mm fall O 11.5mm rise O 15.1mm fall O 15.1mm rise
I need help in solving this problem.
For a thin walled cylinder with diameter of 7.50 meters and 25mm thickness, when applied with internal pressure of 0.85MPA, the resulting tangential stress is 127.5MPA, what would be the longitudinal stress relationship? Choose the nearest answer. A 47 MPa В) 85 МPа (c) 510 MPа 255 MPa E) 65 MPa
A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30 degC. Determine the correct length of the line if the tape used is of standard length at 20 degC under a pull of 5.5 kg. Assume that the cross-sectional area of the tape is 0.025 cm², elastic modulus of tape is 2.10 x 106 kg/cm? and coefficient of linear expansion of steel is 11.6 x 106 per degC.
B.layer question,
3