a) A stream flowing at a rate of 15000 mol/h containing 25 mole % Nz and 75 mole% Hz is to be heated from (35°C) and (300°C). Evaluate the heat transferred using C data given below b*103 4.12 0.96 c*10 11.32 d*109 -3.12 0.693 Gas a 22.3 N2 Hz 21.56 -0.132

a) A stream flowing at a rate of 15000 mol/h containing 25 mole % Nz and 75 mole% Hz is to be heated from (35°C) and (300°C). Evaluate the heat transferred using C data given below b103 4.12 0.96 c10 11.32 d*109 -3.12 0.693 Gas a 22.3 N2 Hz 21.56 -0.132

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The expression for the Joule Thompson coefficient for a gas described by the van der Waals equation of state, at low pressures, can be expressed as: 1 2a -—- (2017-b) Cp\R* T i) What will μT be for an ideal gas? Why must this be the case? ii) How does this expression simplify at high temperature? a) Will μT be positive or negative? b) How does temperature change under conditions of low pressure and high temperature, when this gas expands? iii) How does this expression simplify at low temperature? a) Will μT be positive or negative? b) How does temperature change under conditions of low pressure and low temperature, when this gas expands? iv) Calculate the Joule Thompson coefficient of ethane at 300K and 600K. HJT = You can find the heat capacity needed at the NIST Webbook. Search for ethane and then go to the "Gas phase thermochemistry data." Use the values for 1 bar. Pay close attention to units. Your answer should have units of K/atm. The vdw parameters for ethane are: a…
PLEASE HELP ANSWER THIS THERMODYNAMICS PRACTICE QUESTION THANK YOU
3 Determine the mass of 0.25 m° of steam at 5 bar pressure and 0.85 dryness fraction. 3 Proceed to calculate the heat content 1 m° of this steam.
Use the data from this table of thermodynamic properties to calculate the values of AS for each of the reactions at 25 °C. C(s, graphite) + H, O(g) CO(g)+ H,(g) AS = N, (g) + 3 H, (g) - 2 NH,(g) AS = K Question Source. McQuar
11. Consider cylinder A and cylinder B each A having 1 kg of air (R = 287 J/kgK, y = 1.4). The B air in cylinder A 300 K B is perfectly insulated. Cross sectional area of piston of cylinder A and B are 0.4 m² and 0.6 m² respectively. Now the content of cylinder a is heated quasi statically such that the ari pressure as 100 kPa. air as perfect gas and neglecting the area of cross section of rod, done by the air in cylinder a on the air in cylinder B is (a) 20.72 k]/kg (c) 72.08 k/kg (b) 45.08 kJ/kg Tiwari 30.05 k/kg t Tlay "ut Tiwari
The compression factor of a van deer Waals gas at 100°C and 100 atm given that a= 1.345 atm-L^2/mole^2 and b=0.0322 L/mole
a) In a simple experiment, a solid with a diameter 3 mm and density 1500 kg/m3is released from a tall tower containing air at 25 oC and 1 atm. The inside diameter of the column is 0.15 m. The density of the air is assumed to be 1.2 kg/m3. List all your assumptions and estimate the minimum height of the tower to make sure the particle reaches its terminal velocity before it hits the bottom of the tower. b) In another experiment, 5 kg of the solid particles are to be fluidized with air at 1 atm and 25 oC. The diameter and density of the particles are 3 mm and 95 kg/m3, respectively.Using the Ergun Equation, determine whether the flow of the air is laminar orturbulent. List all your assumptions.
What is the Δr xn G o (in KJ/mole) for a mole of an ideal gas as pressure changes from 0.1 Pa to 1 x10 5 Pa? (NOTE: Express answer in THREE SIGNIFICANT FIGURES.)
What is the enthalpy of steam at 155 deg C? Find the specific enthalpy of superheated steam at 2 atm and 900°C.
Problem 1 0.1 moles of an ideal gas at pressure p= 1.000 bar is confined to a cylinder by a piston. The apparatus is thermostatted at T = 300 K. A weight of mass m is placed on the piston, and the gas expands until its pressure has dropped to 0.9600 bar, lifting the mass through a height of 0.500 m. (1) What is the largest value that the mass m can have in this process? (2) After the expansion is complete, we remove the mass m and replace it with a weight of larger mass m'. The piston now falls back through 0.500 m, compressing the gas, and returning the gas to its initial thermodynamic state. What is the smallest value that m' can have in this process? (3) Assuming that m has its maximum value, and m' its minimum value, compute the total thermodynamic work for this cyclical process. Is net work done by the system, or on the system, or is no work done? Draw a qualitative graph on a pV plot that illustrates what you have found. We will see later that your result is a consequence of the…