A 50-m steel tape weighs 0.04 kg/m and has a cross-sectional area of 0.022 sq. cm. It measures correctly when supported throughout under a tension of 8.0 kg and at a temperature of 20 degrees Celsius. When used in the field, the tape is only supported at its ends, under a pull of 9.0 kg, and at an average temperature of 28 degrees Celsius. What is the distance between the zero and 50-m mark? O a. 47.98 m O b. 48.89 m O c. 49.90 m O d. 50.09 m

A 50-m steel tape weighs 0.04 kg/m and has a cross-sectional area of 0.022 sq. cm. It measures correctly when supported throughout under a tension of 8.0 kg and at a temperature of 20 degrees Celsius. When used in the field, the tape is only supported at its ends, under a pull of 9.0 kg, and at an average temperature of 28 degrees Celsius. What is the distance between the zero and 50-m mark? O a. 47.98 m O b. 48.89 m O c. 49.90 m O d. 50.09 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Ex 5.2: Calculate the lateral strain for a mild steel rod subjected to an axially load causing an axial strain of 0.005 mm/mm if Poisson's ratio is 0.3.
Calculate the Stresses involved in the beam
Activity 3 Questions WHAT'S YOUR SCORE? Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15 mm. Determine the largest allowable value of P if the shear stress in the shaft is not to exceed 120 MPa and its angle of twist is limited to 5º. Use G = 80 GPa for steel. (Note: Two values of P are to be compared here). 300 mm 500 mm
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
Please show a detailed solution and explanation including its FBD. Thank you!
Solve ASAP
Calculate the moment of Resistance of the given beams. If the maximum stress is 100 N/mm2. 190 |不 15 (i) 550 k10> (all dimensions in mm)
O A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 KN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E,µ,G and K.
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
A steel tape is 30 m long under a standard pull of 6 kg with a constant cross-sectional area of 0.05 cm^2. If the normal tension applied to make the tape equal to its nominal length when supported only at the end points, that is the effect of sag will be eliminated by the elongation of the tape due to the application of this load is equal to 14 kg, determine the total weight of the tape. Modulus of Elasticity of tape is 2x10^6 kg/cm^2.
NEED IN 10 MINUTES PLEASE THANK YOU
Determine modulus of elasticity