.A 40 mm diameter shaft issubjected to a twisting momentM, . If max shear stressdeveloped in shaft is 5 N/mm2,what is the value of thetwisting moment ?a. 628.8 Nmb. 638.4 NmC. 62.8 Nmd. 30.4 Nm

Given data : Maximum shear stress (ζMax)=5 N/mm2Diameter of shaft (D)=40 mmTo find :Twisting moment

A 40 mm diameter shaft is subjected to a twisting moment .If max shear stress M, developed in shaft is 5 N/mm2, what is the value of the twisting moment ? a. 628.8 Nm b. 638.4 Nm C. 62.8 Nm d. 30.4 Nm

A 40 mm diameter shaft is subjected to a twisting moment .If max shear stress M, developed in shaft is 5 N/mm2, what is the value of the twisting moment ? a. 628.8 Nm b. 638.4 Nm C. 62.8 Nm d. 30.4 Nm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Describe one of the key duties of engineers: the preparation of capital budgets.

A: An engineer is someone who utilizes scientific knowledge to design, build, and repair engines and…

Q: Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for…

Q: Pa. Determine the magnitude of the angle of twist in a

Q: determine the principal stresses at the point.

A: Principal stresses

Q: A plate with a 1.5-cm diameter circular hole is exerted with the bending moment M = 40 N-m. The…

A: Given bending moment , M = 40 Nm Sy = 400 MPa width of plate, b =3-dia of hole =(3-1.5)cm depth, d =…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given data in question Torque 2410 Nm Outside Diameter D0 75 mm Thickness 5 mm Shear modulus 80 GPa…

Q: 1.) Solve the bending stress about poin and B 200kN m

Q: The cross-section of a shaft 90 mm diameter is subjected to a bending moment of 6 kNm and a twisting…

Q: Figure Q3 (a) shows an overhanging beam ABC subjected to a uniformly distributed load w along AB and…

A: yield stress of the material is 250 MPa

Q: The shaft is hollow (outer diameter d, = 295 mm and inner diameter d, = 250 mm) and delivers 1,700…

A: Given Data: It is asked to draw the Mohr's Circle.

Q: 200 mm If the beam is subjected to a bending moment of M=50KN, determine the maximum bending stress…

A: Using formula to find bending stress

Q: In the figure, forces with resultant intensity Fx = 3P (unit N), Fy = 2P (unit N) and Fz = P (unit…

A: the largest P value according to the Von Mises assumption for the cube to be safe = 20a23explanation…

Q: 2 KN.m 350 mm 50 mm 200 mm columna 175 mm 2 m 1 m 8 m

A: as support are simply suppourted.max BM= BMmax=wl28 =2*828 =16KNM

Q: 2. Determine the shearing stress in each of the four walls of a portion of a structural aluminum…

A: Given, Torque =3 kN-m=26.55 kip-in Dimension=100×51 mm=3.93×2 in Wall thickness=4 mm=0.15 in.

Q: In a 2 dimensional stress anal ysis, the state of stress at a point is shown below in which length…

Q: Draw the torsional moment diagram. Determine the torsional angle CA (rotation angle) that will occur…

Q: (2) A square member (400mm x 400mm) sustains an internal shear force of 150 kN and an internal…

A: Given: A square cross section of 400mm × 400mm Shear force = 150KN Bending moment = 250KN-m…

Q: The following shaft has a diameter of 60 mm, and it is made of Aluminum (G = 29 GPa). The shear…

A: Given, d=60 mmG=29 GPaτ= 200 MPaFOS=2.5ϕ=3 degree

Q: In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in.…

A: A) Given data ; E = 30 X 106 psi Thickness = 0.175 inches Length is = 48 inches To Find : Determine…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: Given Outside diameter (Do) = 75mm Thickness of wall (T) = 5mm Torque (T) = 1680 N-m Shear modulus…

Q: A solid circular shaft of 60mm diameter transmits a torque of 1800 Nm. The value of maximum shear…

Q: A solid 27 mm diameter shaft is subjected to an axial load of P = 50 kN and a torque of T acting as…

Q: The plastic hexagonal tube shown in Figure (3), is subjected to a torque of 150 N. m. Determine the…

Q: Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b.…

Q: For the figure shown, A compound shaft composed of bronze, aluminum and steel segments is fastened…

A: Given Required Maximum shear stress in Aluminum and bronze

Q: A solid shaft with diameter D mm and L mm long is supported between two bearings at the ends as…

A: "Since you have posted a question with multiple sub-parts. We will solve the first three sub-parts…

Q: An element in plane stress from the frame of a racing car is oriented at a known angle 0 (see the…

Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…

A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: A hollow tube ABCDE constructed of monelmetal is subjected to five torques acting in the…

A: Given:- T1 = 1000 lb-in., T2 =T4 = 500 lb-in., andT3 =T5 = 800 lb-in To find:- maximum permissible…

Q: 3. The shaft in the figure below consists of 75 mm diameter bronze segment that is rigidly joint to…

A: Solution:- We know that, torsion equation is TJ=τr=GθL by using this relation, the stress in AB…

Q: The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa…

A: To find out the maximum shear stress in each shaft.

Q: nd shaft, composed of steel, aluminum, and bronze segments, car developed in each material. The…

Q: A hollow circular bar of cylindrical steel is 1.5 m long and has inner and outer diameters of 40 and…

A: I think the second answer that you provided is wrong plz recheck it I have tried to solve carefully…

Q: A closed cylindrical tank, placed horizontally, 410 mm in internal diameter and 2.0 mm thick is…

Q: 150 mm t = 4 mm -t =3 mm t = 4 mm 75 mm 50 mm t = 2 mm 50 mm

Q: 1. The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

.A 40 mm diameter shaft is
subjected to a twisting moment
M, . If max shear stress
developed in shaft is 5 N/mm2,
what is the value of the
twisting moment ?
a. 628.8 Nm
b. 638.4 Nm
C. 62.8 Nm
d. 30.4 Nm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Help please!
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm2. The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. Find the magnitude P of the largest additional vertical force that can be applied to the bar.___________kN in 2 decimal places Take note: Write it on a paper, hand written showing correct answer.
The following stress element represents the stress state at point A of the structure in the figure below. Determine the maximum shear stress in this condition. 52.8 MPa 26.4 MPa O a. 32.78 MPa O b. 29.65 MPa Oc. 40.25 MPa O d. 37.34 MPa
Q3: Three segments of elliptical solid steel section, circular solid aluminum section and circular solid bronze section were assembled to form the shaft shown in Figure (3). Determine the generated stress in each material when the support at D is able to rotate until 0.035 radian based on the two torques T1 and T2 of 450 N.m and 750 N.m, respectively. 94= 834 v5? AL:28 1 Steel Ahminum Bronze T2 D= 70 mm D= 100 mm 1.5 m 1.5m 2.0 m 25 mm Figure (3) 145 mm
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Let T = 39 MPa and o = 19 MPa. Determine the center ocenter of the corresponding in- plane Mohr's circle. 50 MPa -21.56 MPa O -17.85 MPa O -10.87 MPa -14.07 MPa -15.50 MPa
Calculate the value of Q and t that are used in the shear formula for finding the shear stress at A. 0.3 m 0.3 m 0.2 m 0.2 m 0.4 m 0.km 0.2 m
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 1120 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft. O 0.0145 rad 0.0280 rad 0.0207 rad O 0.0192 rad O 0.0241 rad
8.19 A solid circular shaft is subjected to a torque T(in Nm), which produces a maximum shear stress of f(in N/mm²) in the shaft. The required diameter of the shaft would be
In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: у P = 400 KN X 30 mm 1000 mm 30° Area 20 mm الاختيارات 577 O 597 587 O 567
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
A high-strength steel [E = 188 GPa] tube having an outside diameter of 67 mm and a wall thickness of 4.1 mm is bent into a circular curve having a 42-m radius of curvature. Determine the maximum magnitude of the bending stress max developed in the tube. Answer: Omax = i MPa.