A 130-mm-diameter cylinder contains 140 cm³ of water at 70°C. A 60-kg piston sits on top of the water. If heat is added until the temperature is 200°C. The work done in kJ is O 37.9391 O 41.8515 O 46.28526 O 33.33973

Q: Q1) a hot gas at 325°C flows through a metal pipe of 10 cm OD and 3 mm thick. It is insulated with a…

A: Given Data  To Find The insulation thicknessHeat loss per m length of the pipe

Q: 1. A 7-meter-long steel pipe was installed by a man during a cold whether at 20°C. What would be the…

A:

Q: an insulated piston-cylinder assembly initially at constant pressure of 250 kPa There is 4 L of…

A: Given data:   Pressure of piston-cylinder assembly = 250 kPa Volume of saturated liquid water = 4 L…

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: Athin isothermal disk, having a diameter of 1.8 cm, is maintained at 40◦C and buried in a…

A: Given  thermal conductivity k= 0.8 W/m· ◦C  diameter of disk is D = 1.8 cm  radius = 0.9 cm = 0.009…

Q: Write a process path for the heating and compressing of nitrogen. Include the state of the coumpound…

A: Given, Initial temperature, T1 = 293.15 K Initial pressure, P1 = 2×105 Pa Let the moles of the gas…

Q: heat transfer during this process

A:

Q: Determine the standard heat for: H2S(g)+2H20(g) 3H2(9)+S02(g) at 1000K

A: Given Reaction,                   H2S (g) +2H2O (g)→3H2 (g) +SO2 (g)     we have to determine the…

Q: The process of injecting water into a well under high pressure is called Thermal EOR a. False b.…

A: The oil is recovered from the reservoir by means of natural energy (pressure difference) but when…

Q: 4. Which property of a system increases when heat is transferred: (a) at constant volume, (b) at…

A:

Q: In the case of determining heat rates and fluxes, is power required for the system the same as the…

A: Heat rate: Heat rate is defined as amount of heat (energy) per unit time. Unit of energy may be…

Q: Steam at 235°C is flowing inside a steel pipe (k = 61 W/m ∙ °C) whose inner and outer diameters are…

A:

Q: A spherical stainless steel storage tank (k = 20 W/m.K) with 1.8 m inner diameter and 3.7 m outer…

A:

Q: How many heat are needed to change 50 kg of ice at -10.0 °C to steam at 250 °C?

A: Given: m  = 50 kg Ti = -10.0 °C (Ice) Tf = 250 °C (Steam)

Q: I understand that we have to use this formula Heat current=(k. Area. change in temperature)/length…

A: Firstly, the brass rod one end is in boiling water, which means this rod is hot. While the Copper…

Q: 12. Water at a rate of 1 lbm/s flows in a vertical heated tube (d = 1.5 in). System pressure is 1250…

A:

Q: A. Identify the type of thermodynamic systems involved and the heat and work flows and their…

A: Hi, since there are multiple questions posted, we are allowed to answer one question per submission.…

Q: A carnot machine operating between 500 K and 298 K temperatures produces 1500J of work in each…

A: Carnot engine is basically operates based on Carnot cycle. Carnot engine is a theoretical heat…

Q: A pipe (ID: 130 mm, OD: 165 mm, k=15 W/m²-K, Length: 2 meters)is insulated with several materials,…

A: Given Pipe Di=130mm D0=165mm K=15 W/(m2K) L=2m Inside fluid –Oil temperature T1=118℃ Insulation is…

Q: 8. For polytropic process the heat and work can not cross the boundary of the system * False True

A: Given, Concept of Polytropic Process Find,  For polytropic process the heat and work cannot cross…

Q: How many heat are needed to change 50.0 grams of ice at -15.0 °C to steam at 120.0 °C?

A: Given: mass of ice = 50g=50g×kg1000g=0.05kg temperature of ice = -15°C=-15+273K=258K temperature of…

Q: What is the principle of thermal balance? th

A: Given  Term - Thermal balance Find what is the principle of thermal balance

Q: An automobile engine provides 596 Joules of work to push the pistons and generates 2246 Joules of…

A: Given that, Work done on the system W = 596 J Heat generated by the system Q = 2246 J It is required…

Q: If a heat pump works between-15°C and 50°C. Then, the coefficient of performance is... Select one:…

A:

Q: Q.2 An Aluminum plate of area 500cm2 is heated up for 5 seconds and its temperature increases from…

A: Area of Aluminium Plate=500cm2=0.05m2 Thickness=2cm=0.02m Mass of Aluminium plate=3.46kg Time up to…

Q: calculate applied pressure for expansion volume of inert nitrogen gas if the change of volume 20 cm³…

A:

Q: 600 kW of heat is removed from a heat exchanger with 200 mol/s formaldehyde flowing through. The…

A:

Q: Which of the following is not an intensive

A: Intensive property is a thermodynamic property which does not depend on the amount of material in…

Q: Imagine gas in a piston – cylinder device. The fluid is compressed resulting to an increase in…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 7.1 What is condenser ? 7.2 What are the functions of a condenser in a thermal power plant? Give the…

A: A condenser is an essential component in thermal power plants, converting exhaust steam back into…

Q: (For Nos 4 to 6). Heat Loss from a Pipe. A bare stainless steel tube having an outside diameter of…

A: Given Data: Outside diameter; D=76.2 mmD=0.0762 m Emissivity; ε=0.55 Temperature; T1=366.4 KT2=294.2…

Q: Gases inside a cylinder are ignited causing a reaction with a heat loss of 1000 joules. The…

A: Heat loss to the surrounding, dQ=-1000joules (heat transfer to the system possitive, heat transfer…

Q: A piston-cylinder assembly contains ammonia, initially at a temperature of -20°C and a quality of…

A: Initial state temperature of ammonia, T1 = -20oCInitial quality of ammonia, x1 = 50%Final state…

Q: 6. Hot water at 90°C heats air from a temperature of 0°C to 20°C in a parallel flow heat exchanger.…

A:

Q: Solve for the amount of heat (in kJ) of 10 galloon of cooling water transferred from an engine to…

A:

Q: 5 kg liquid water is heated on a stove from 30 to 90C, how much work is required if specific heat is…

A: The energy can neither be created nor destroyed. Energy in the universe is constant. One form of…

Q: A piston-cylinder assembly has 1 kg of air at 700 kPa and 400C. The piston cross-sectional area is…

A: This problem is based on the concept of ideal gas law. The data given : Initial temperature ,T1 =…

Q: Consider 2 kg of air has a decrease of internal energy of 25 kJ during a reversible non flow…

A:

Q: In an engine working on an ideal otto cycle, the temperature at the beginning and end of the are…

A: Temperature at the beginning and end of the compression respectively 320C and 4240C.

Q: An air-standard Diesel cycle has a compression ratio of 16 and a cutoff ratio of 2. At the beginning…

A: Given: Air-Standard Diesel cycle Compression ratio 𝞬c=16=V1V2 Cutoff ratio 𝞪=2=V3V2 At the…