A 10 KVA, 840/240-V, 60 Hz, Y-Y, 3-phase transformer is supplying 6 KVA of power to a load at 0.9 Lagging power factor, a line load voltage of 240 Volts. Its per-phase equivalent circuit is given below. Calculate the magnitude of the line input voltage of this transformer. 3.51, 0.425 + jl.2 2 Vp 3.5 7682 1250O

A 10 KVA, 840/240-V, 60 Hz, Y-Y, 3-phase transformer is supplying 6 KVA of power to a load at 0.9 Lagging power factor, a line load voltage of 240 Volts. Its per-phase equivalent circuit is given below. Calculate the magnitude of the line input voltage of this transformer. 3.51, 0.425 + jl.2 2 Vp 3.5 7682 1250O

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1 + j1 Ohms, and the secondary impedance is 0.2 + j0.2 Ohms. Assume the core impedance (R0 and X0) can be neglected. A resistive load of 12 Ohms is connected to the secondary. What is the primary current magnitude? What is the secondary voltage magnitude? What is the efficiency of this transformer with this load?
In the transformer circuit below, a load of 2.5cis20° Ohms is connected to the output terminals of the transformer. If the voltage across the load is 230V, determine:a. Load current, I(L)b. Imc. Icd. Source voltage, V
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
For a 50 kVa distribution transformer, which on its high voltage side is 2400 V and on the short-circuit low voltage secondary has a voltage of 240 V with a frequency of 60 Hz, it has a leakage impedance of 0.72+j0.92 Ω on the high voltage side and 0.0070+j0.0090 Ω on the high voltage side low tension. The short-circuit test presented values of 48 V, 20.8 A and 617 W for high voltage. The impedance responsible for the excitation current is 6.32+j43.7 Ω referring to the low voltage side. One open circuit test, with the low voltage side energized, presented the values of 240 V, 5.14 A and 186W. According to the information presented, determine: a. Draw the equivalent circuit on the high voltage side and present the impedance values in the circuit. b.Draw the equivalent circuit on the low voltage side and present the impedance values in the circuit. c. For the high voltage value, calculate the value of the current flowing in the magnetizing impedance. d.Determine the yield for an…
Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage reactance/phase of the primary winding are 0.78 N and 4.80 and the corresponding values for the secondary winding are 0.012 and 0.062 respectively if the primary winding is connected in delta and secondary in star calculate: i)The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited Ii) The full load copper loss
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
In part c determine the voltage across Rp and Xp .
Example 5 A 600 kVA transformer has a primary winding resistance of 0.62 and a secondary winding resistance of 0.002 2. The iron loss is 2.6 kW and the primary and secondary voltages are 6 kV and 330 V respectively. If the power factor of the load is 0.8, determine the efficiency of the transformer (i) on full load, and (ii) on half R.. load.