A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)? (A) 644.11 ppm CaCO3 (B) 626.71 ppm CaCO3 C) 633.43 ppm CaCO3 D) 637.27 ppm CaCO3

A 0.3045 g of CaCO3 primary standard was dissolved using concentrated HCl, evaporated to incipient dryness, and quantitatively transferred to a 250 mL volumetric flask and diluted to mark. A 10 mL of aliquot was then transferred to an Erlenmeyer flask, together with 5mL buffer and 5 drops of EBT indicator, and was used to standardize the EDTA titrant. The solution turned blue after the addition of 24.10 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. [Analysis] A 30 mL unknown water sample was treated with 37.6 mL of EDTA. A blank correction was made and was determined to be 0.4 mL. What is the concentration of CaCO3 of the unknown water sample in ppm? (MW CaCO3 = 100.0869 g/mol)? (A) 644.11 ppm CaCO3 (B) 626.71 ppm CaCO3 C) 633.43 ppm CaCO3 D) 637.27 ppm CaCO3

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

COMPLEXOMETRIC TITRATION A deep well sample of 100 mL was titrated with 0.010 M EDTA at pH=10 (with Mg-EDTA-PH10 reagent) and consumed 31.95 mL using EBT indicator. Titration of another 100 mL of the same deep well sample with the same titrant but the pH was adjusted to 12.10 and murrexide as indicator consumed 24.25 ml to reach end point. Calculate: А. Total Hardness of water as CaCO3 В. ppm of Ca and Mg 76
A 1.000 mL aliquot of a solution containing Cu²+ and Ni²+ is treated with 25.00 mL of a 0.03703 M EDTA solution. The solution is then back titrated with 0.02138 M Zn²+ solution at a pH of 5. A volume of 22.13 mL of the Zn²+ solution was needed to reach the xylenol orange end point. A 2.000 mL aliquot of the Cu²+ and Ni²+ solution is fed through an ion-exchange column that retains Ni²+. The Cu²+ that passed through the column is treated with 25.00 mL of 0.03703 M EDTA. This solution required 18.53 mL of 0.02138 M Zn²+ for back titration. The Ni²+ extracted from the column was treated witn 25.00 mL of 0.03703 M EDTA. How many milliliters of 0.02138 M Zn²+ is required for the back titration of the Ni²+ solution? volume: mL
What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA solution? Assume that 1.758 M EDTA solution was computed based on the titration of CaCO3 standard. The volume of titrant needed to reach the endpoint was 35.00 mL. Ca2+ + Y4- → CaY2- 0.1500 g 5.630 g 6.158 g 0.6158 g
If a 25.00 ml aliquot of a solution containing sulfide ions was added to 25.00 ml of 0.0108 M Cu2+ solution. The CuS precipitate was washed and collected. The pH of the combined filtrate and washings was then adjusted by the addition of ammonia and the solution was titrated with 0.01453 M EDTA, using a suitable indicator. The endpoint volume was found to be 12.12ml. Find the molarity of the sulfide in the sample solution.
Standard oxylate solution used to standardize KMnO4 was prepared by dissolving 3.299g of Na2C2O4 in 1.000L of water containing H2SO4. add 25mL aliquot of the Na2C2O4 solution required 28.39 mL of KMnO4 for titration. A blank titration of 25mL of water containing H2SO4 required 0.03 mL of KMnO4. what is the molarity of the KMnO4 solution? 5C2O42-+2MnO4-+16H+ → 10CO2+2Mn2++8H2O
a 20 ml portion of a deep well water sample was diluted to 250 ml solution. a 50 ml aliquot of this diluted sample water was buffered at ph 10 and required 8. 50 ml of a standard EDTA.the titrant was standardized using 100ml containing 0.8622 mg primary standard calcium carbonate , which required 15.45 ml for titration.(a) identify a possible indicator and its endpoint color (b) calculate the molarity of the EDTA solution. (c) calculate the total hardness of the water as ppm CaCO3 (d) identify the quality of the water sample in terms of hardness
Calculate the final concentration of citrate buffer in a test tube containing the following components: 250 µl of 25 mM p-nitrophenol phosphate, 100 µL 0.5 mg.ml-1 acid phosphatase and 150 µl 100 mM citrate buffer pH 4.8. Provide the answer together with unit in the answer box.
Complexometric titration must be performed at pH 10.0 True False
An unknown solution containing 25.00 mL of Ni2+ in dilute HCl is treated with a known excess of 25.00 mL of 0.05382 M EDTA solution. The solution turns yellow when a few drops of indicator are added. The excess unreacted EDTA back titrated with 0.02299 M Zn2+, which requires 17.00 mL to reach the red end point. What is the molarity of Ni2+ in the unknown solution?
SO3 + H20 by titration with permanganate in acidic pH: peroxide was diluted to 25 ml and analyzed The sample required 84.2 mL of 0.0175 M permanganate to reach the concentration of hydrogen peroxide in the original sample? 04+H202 →02 + Mn2+ NT COPY NRSITY What is the GE
A solution containing Mg2+ was buffered to pH 9.81 and titrated with EDTA. Eriochrome black T, with p?a1 = 6.3 and p?a2 = 11.6 was used as the indicator. It is a diprotic acid, H2E What is the fraction of the predominant form of eriochrome black T in solution at this pH? (To answer this, report the alpha fraction of the indicator’s most prevalent species at this pH)