7-7 In a step-up converter, consider all components to be ideal. Let V be 8-16 V, V,(regulated), f,in a continuous-conduction mode if P, 2 5 W.= 24 V20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operating

Answered: Image /qna-images/answer/0e2b5c28-e9b1-4e79-aeb0-036ae3bd7919.jpg

7-7 In a step-up converter, consider all components to be ideal. Let V, be 8-16 V, V, = 24 V (regulated), f. = 20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operating in a continuous-conduction mode if P, 2 5 W.

7-7 In a step-up converter, consider all components to be ideal. Let V, be 8-16 V, V, = 24 V (regulated), f. = 20 kHz, and C = 470 µF. Calculate Lmin that will keep the converter operating in a continuous-conduction mode if P, 2 5 W.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

image 93
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V
S-4) The input signal Vin of the clipper circuit given below is a sinusoidal signal of Vp-p = 30V and the wave the form is as given in the figure. a) Plot the output waveform of this circuit in the area given for + and - alternans. b) Calculate the peak values of the output and indicate it on the graph. Note: Diode threshold voltage will be 0.7V
A step down de chopper is connected to an R5 2 and L-10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, lo and the peak to peak ripple current as an absolute value and as percentage of de value.
A buck-boost converter operates with an input battery. It converts +12 V to –12 V at apower level of about 75 W. the switching frequency is 120 kHz. The switches have200 ns switching time. The battery has an internal series resistance of 0.2  and seriesinductance of 200 nH. (a) What is the operating value of the duty ratio? What power is lost in the battery resistance? (b) Propose an interface structure to improve operation and decrease losses. What are the duty ratio and battery resistance loss with your interface in place?
An RL load (R=0.2 Ohms, L=10 mH) is controlled by a converter. The supply voltage Vs is 600V and the chopper frequency is 200 Hz. The maximum peak to peak ripple current is equal to: Select one: a. 30A b. 55A c. 90A d. 75A
b) A Buck-Boost converter has an output of 24 V from a 5 V input with diode ripple current of 2.4 A and switching frequency of 100 kHz. Find the duty cycle and the inductance of the converter.
This one.
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple Values 35 V 60 kHz 5 % 1% a) Sketch the final converter and label all parameter values b) Sketch the final operating waveforms and label all parameter values c) Determine Ve.min and Vemax- Check if the output voltage ripple matches with the design requirement.
Q.1) The step-down converter shown below has a pure resistive load of value 10 2. The input supply voltage is Vs=110 V. The switch (SW) can be assumed ideal. For a chopping frequency of value f= 5 kHz and a duty cycle of value 75 %, perform the following: a) Draw the waveforms of the voltages across the load resistance (R), across the switch (SW), and across the diode (D). b) Draw the waveforms of the currents in the load resistance (R), in the switch (SW), and in the diode (D). c) calculate the average value of the load voltage. d) calculate the rms value of the load voltage. e) calculate the power consumed by the load. f) calculate the effective input resistance of the converter. SW Vs D
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.
Sub:power electric