60N L 30 Q 3m 40° 150N A 90N SON P 4. Which of the following force diagrams shows correctly the reactions at the supports? A. 60N C. Lxt L Q 60N 3m 40° Ax+ ISDN 3m 40° m O ISON 0 O 90N 90N SON P It is statically determinate. It is statically indeterminate. It is ill-arranged. It is geometrically unstable. → SON P B. 60N Lxt Lxf Q 60N Q 3m Axt 40°C O ISON m 40° 3m ISON 21 O 90N 90N SON P SON P 5. Which of the following statements is TRUE about the circular plate?

60N L 30 Q 3m 40° 150N A 90N SON P 4. Which of the following force diagrams shows correctly the reactions at the supports? A. 60N C. Lxt L Q 60N 3m 40° Ax+ ISDN 3m 40° m O ISON 0 O 90N 90N SON P It is statically determinate. It is statically indeterminate. It is ill-arranged. It is geometrically unstable. → SON P B. 60N Lxt Lxf Q 60N Q 3m Axt 40°C O ISON m 40° 3m ISON 21 O 90N 90N SON P SON P 5. Which of the following statements is TRUE about the circular plate?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam has a lenght of L = 8 m long and carrying the uniformly distributed load of w = 5 kN/m. w kN/m A B RA RB a) Calculate the reaction at A. RA= kN b) Calculate the maximum bending moment. Mmax= kNm
Find the forces in every member.
The A-36 steel rod has a diameter of 60 mm and is firmly attached to the rigid supports at A and B when the initial temperature is 75°C. If the temperature becomes 30°C and an axial force of 300 kN is applied to its center, determine the reactions at A and B in kN Where: a=12x10^6 m/(m°C), E = 200 GPa and L = 500 mm A B
Rigid bar ABC is supported by two identical solid bronze [σY = 331 MPa; E = 105 GPa; α = 22.0 × 10−6/°C] rods and a single solid steel [σY = 250 MPa; E = 200 GPa; α = 11.7×10−6/°C] rod. Bronze rods (1) each have diameters of d1 = 26 mm and lengths of L1 = 3.3 m. Steel rod (2) has a length of L2 = 4.4 m. (a) Calculate the diameter d2 required for steel rod (2) so that the deflection of joint B is zero for any change in temperature.(b) Using the value of d2 determined in part (a), determine the maximum temperature decrease that is allowable for this assembly if a factor of safety of 2.4 is specified for the normal stress in each rod. Since the temperature is decreasing, the answer should be negative.
Determine the reactions at the supports of the following beam. P=20 kN
X = 212 Y= 94 A = 2 B = 1
6. The upper beam in the figure is supported by a reaction at R3 and roller at A which separates the upper and lower beams. Determine the values of the reactions. 600 Ib 190 lb 4000 Ib 10' 4' -4' A -10' -4' -10' R3 R1 R2
Find the zero force and the reactions Explain why they are zero forces
Please solve all parts correctly. Don't copy please
the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees, belta=47 degrees. determine the reaction at b in kN. support A is a roller and Support B is hinge.
solid mechanics Find the moment of the force F in the figure about the ACaxis. 4 m 3 m 2 m B F= (41+ 12J-3k)N
3 ft 100 lb 3 ft- 200 lb-ft 2 ft 000 Az □ Ay DO 000 NA along the rod MA B₂ By Fa perpendicular to the rod No perpendicular to the surface at B MB L. Identify the support reactions on the smooth uniform bar shown in (Figure 2). Check all the possible support reactions on the beam, even if some of them are equal to zero due to the loading given. Make sure the reactions in the set you choose do not depend on each other.