6. A 4 pole DC shunt generator with wave wound armature having 390 conductors has to supply a load of 500 lamps each of 100W at 250 V. Allowing 10 V for the voltage drop in the connecting leads between the generator and the load and brush drop of 2V. Calculate the speed at which the generator should be driven. The flux per pole is 30mWb and Ra = 0.05 ohms and Rsh = 65 ohms.

6. A 4 pole DC shunt generator with wave wound armature having 390 conductors has to supply a load of 500 lamps each of 100W at 250 V. Allowing 10 V for the voltage drop in the connecting leads between the generator and the load and brush drop of 2V. Calculate the speed at which the generator should be driven. The flux per pole is 30mWb and Ra = 0.05 ohms and Rsh = 65 ohms.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
Question No.4 A dc generator has an armature emf of 100 V when useful flux/pole is 20 mWb, and a speed of 800 rpm. The generated emf at a speed of 1000 rpm and same flux is
Problem #1: A 6-pole, 3-phase, Y-connected, 60-Hz alternator has 12 slots per pole and 4 conductors per slot. The winding is 5/6 pitch. There are 0.025 Wb entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. Determine (a) pitch factor (b) distribution factor (c) induced emf per phase
Dc machine.............
A 6 pole DC wave wound generator has 41 armature conductors with Flux per pole is 26 mWb and the e.m.f generated is 79 V, then the speed of machine is ?
An 6-pole d.c. generator has 515 armature conductors, and a useful flux of 10 mWb per pole. What will be the e.m.f. generated if it is lap-connected and runs at 970 rpm? What must be the speed at which it is to be driven produce the same e.m.f. if it is wave-wound? Eg Speed
I want calculation step by step
Please answer both subparts i will really upvote. Thanks
There are 175 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 130° electrical and the flux per pole is 0.04 Weber sinusoidallly distributed. Calculate the emf induced per phase.
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage
6 shunt generators are running in parallel in a curtain generating station. Each generator supplies a load current of 500 A at 220 V. The shunt field current of each generator is 5 A and the armature resistance of each machine is 0.05 ohm. If one generator is suddenly switched off determine the percentage change in terminal voltage, the total load current being kept uncharged