6 in a levelling survey, the summation of all backsights and the summation of all foresights are 7,475 m and 7.395 m, respectively. The reduction level of the initial benchmark is 1000.000 m. The reduced level of the of point where the staff is held will be

6 in a levelling survey, the summation of all backsights and the summation of all foresights are 7,475 m and 7.395 m, respectively. The reduction level of the initial benchmark is 1000.000 m. The reduced level of the of point where the staff is held will be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The length of survey line measured by 20 m chain on a - ground sloping at 1:8 was found to be 294.6…

Q: Q.2 Reciprocal leveling was conducted across a wide river to determine the difference in level of…

Q: 1) Compare and contrast: a. Differential leveling and trigonometric leveling b. Trunnion axis and…

A: Compare and contrast A. Differential leveling is used to find out the elevation between 2 points…

Q: Choose the right answer for the following:

A: option a.) grazing is incorrect because grazing angle is less than the incident angle option b.)…

Q: Discuss with relevant examples any three applications of leveling

A: For determining relative altitudes of points on the surface of the earth of beneath the surface of…

Q: In a topographic survey undertaken by Karman Sury. Corp. before any leveling is conducted, the…

A: Given, Instrument station Reading of A (m) Reading of B (m) A hA=1.623 hB=2.875 B hA'=0.362…

Q: 4. For the given set of data of differential leveling as shown in the tabulation: Station Backsight…

Q: Example 5) For the purpose of realizing the work of the dirt dam, the survey was repeated, and the…

A: Given Data: Leveling station is 00+1. Level of leveling station is h=12.06 m.

Q: In surveying of differential leveling runs from BM10 to BM11 at a distance of 7.5km. It was observed…

Q: Triangulation Stations A, B, C, and D have the following observation angle Angle Values ACB 50° BAD…

A: Solution: "None of the options are correct in the above question " The correct value of the angle…

Q: Using a 1 second theodolite the following clockwise angles were measured in a closed traverse. What…

A: The traverse angle is given as follow: 163° 27' 36" 324° 18' 22" 62° 39' 27" 330° 19' 18" 181° 09'…

Q: Q- A survey line was measured to be 285.5m with a tape having a nominal length of 30m. On checking,…

A: Given data- Measured length ML=285.5 m, Nominal length of tape NL=30 m, Tape is 0.05 m too short,…

Q: Surveying The following staff readings were taken in succession with a dumpy level. The instrument…

A: Given data, 1st reading was taken on a BM , RL of benchmark= 200.00m The instrument was shifted…

Q: Among the different methods of leveling; — Differential Leveling — Double Rodded Leveling —…

Q: The readings taken during a levelling operations 1.305,1815, 1.015, 1.245, 1.355,- 2015.0.805/2.015,…

Q: Q2: -The following reading was taken in levelling process as shown in table below, if the reduced…

A: This method is most suitable for the survey operation with the number of intermediate observations.…

Q: Example 5. With what accuracy must the slope angle 5° 30' be measured if the horizontal distance…

A: Slope angle θ = 5o 30' Slope distance S = 1320.50 m accuracy upto 0.005 m, To Find- The value of the…

Q: Jr, a civil engineer was to estimate the height of a transmission tower (G). He performed…

A: Given:- The trigonometric leveling survey data of 3 stations E, Y, & A are given The slope…

Q: Reciprocal levelling is done to test a dumpy level, along a chain line, at a common interval of 25m,…

A: Given DatReduced Levels (RLs) at first station = 97.535 mReadings (BS, IS, FS) = 3.200, 2.135,…

Q: A docs.google.com =6 To establish a new benchmark on point B using a levelling instrument. The work…

Q: Two pegs 'P' and 'Q' were fixed on opposite banks of a river and the following measurements were…

A: Given- Two pegs P & Q fixed on opposite banks of a river- Measurement values- R.L of station P…

Q: The readings from a level instrument are booked from a survey along the line collimation method. If…

Q: Jr, a civil engineer was to estimate the height of a transmission tower (G). He performed…

Q: 2. A reciprocal leveling is observed across a wide river and the reciprocal level readings were…

Q: 1. Solve for the elevation at BM2 Station BS FS Elevation BM1 5.87 392.25m TP1 7.03 6.29 TP2 3.48…

A: Calculate elevation of BM2?

Q: Reciprocal levelling is done to test a dumpy level, along a chain line, at a common interval of 15m,…

A: The readings from the dumpy level are given with 135m as the starting point with 15m intervals,…

Q: If the total distance of third order leveling network is 5546.27 m , the acceptable misclosure of…

A: The acceptable misclosure for 3rd order levelling network is 12K Where, K = Distance in kilometer.

Q: The survey works were carried out using the leveling device and the following readings were taken:…

Q: Among the types of leveling, what seems to be the most essential and why?

A: Given There are different types of levelling listed in the question such as Differential levelling…

Q: Problem 2. A transit is set up at point B which is between A and B. The vertical angle observed…

A: Calculate the vertical difference in elevation between the line of sight (LOS) and A, tan α =…

Q: In a leveling survey, the summation of all back sights and the summation of all foresights are 7.475…

A: Given- Summation of backsights BS=7.475 m, Summation of foresights FS=7.395 m, Bench mark BM=100.000…

Q: In the case of angular measurements being more precise than linear measurements, the traverse can be…

A: The traverse can be balanced using angular measures if they are more accurate than linear…

Q: A student surveys line AB in a level ground field by taping. While taping, he used pebbles as…

A: Given that :- Length of tape = 25 m Pebbles(No.) Partial Distance Trial 1 25 6.345 m Trial…

Q: The readings (2.312, 1.185, -2.365, 0.195, 0.885, 1.345, 0.905) were taken with a level. The…

A: point back bearing fore bearing height of instrument elevation of point remark 100 BM…

Q: then RL (in m) of R is

A: Given data. Rl of point R with respect to the bench mark at P.Staff reading is shown in graph…

Q: Problem: Trigonometric leveling (base of object is accessible) In order to determine the quantity of…

Q: 4. For the given schematic route of a differential leveling, backsights and foresights on series of…

Q: An inverse method of leveling is executed between two existing concrete structures and across a…

A: Given Elevation of A = 240.05 To find elevation of the bottom of the concrete beam of the second…

Q: The following readings were successively taken in levelling work 2.230, 1.605, 0.990, 2.090, 2.865…

Q: An elevation must be established on a benchmark on an island that is 2536.98 ft from the nearest…

Question

6 in a levelling survey, the summation of all
backsights and the summation of all foresights
are 7,475 m and 7.395 m, respectively. The
reduction level of the initial benchmark is
1000.000 m. The reduced level of the of point
where the staff is held will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Elementary Surveying Instructions: Please show complete solutions. Problem: Answer #3, Compute a, b, and c.
Fundamentals of Surveying In leveling across a river, reciprocal level readings were taken between two points A & B. From a set-up near A on A, 0.954 &0.952m, on B 2.086, 2.087, 2.088 & 2.087 m. At the setup near B: on B, 2.450 and 2.448m, on A, 1.362, 1.363, 1.364 & 1.363m What the Elevation at B if Elev at A is 45.75m?
4. For the given set of data of profile leveling as shown in the tabulation: Backsight (m) 1.24 Foresight (m) Station IFS (m) Elevation BM1 1 2.35 1.76 TP2 2.06 2.78 800 3 0.68 4 0.98 2.45 6 2.67 BM2 2.36 a. Find the difference in elevation of Station 6 and Station 2 b. Find the difference in elevation of Station 5 and Station 1 c. Find the elevation of BM2
Can differential leveling be combined with trigonometric leveling in an adjustment? Explain how you would handle their relative qualities in a least squares analysis? Explain properly.
Jr, a civil engineer was to estimate the height of a transmission tower (G). He performed trigonometric leveling from 3 stations E, Y&A, using slope distances and vertical angles. The survey data are as follows: SEG = 678.56; aEG= 5°30' Syg = 555.31; aye= 3°10' SAG = 900.31; a 46= 2°45' Elevations of stations above the MSL datum HE = 253.31 ft| Hy= 287.64 ft. H= 275.11 ft. Compute the elevation at the top of the cell tower from pt. Y Select the correct response: 412.35 ft 318.32 ft 253.32 ft 320.35 ft
A wide river that is connected to the proposed Kaliwa Dam was measured using a reciprocal leveling and the foresights and backsights were taken and tabulated below. If the elevation of M is 5GB.7962 meters, compute the elevation of point N. Instrument set-up near M Instrument set-up near N STA BS FS STA BS FS M 3.3523 N 2.7C54 M 3.5B58 N 2.6E54 M 3.4891 N 2.5514 M 3.3D19 2.4587 N 2.6E52 M 3.1432 N 2.5429 M 3.2G21 N 2.6G65 M 3.3333 N 2.7754 M 3.4F11 N 2.5E45 M 3.1423 N 2.6551 M 3.2244
An elevation must be established on a benchmark on an island that is 2536.98 ft from the nearest benchmark on the island’s shore. The surveyor decides to use a total station that has a stated distance measuring accuracy of (3 mm +3 ppm) and a vertical compensator accurate to within 0.4”. The height of instrument was 5.37 ft with an estimated error of 0.05 ft. The prism height was 6.00 ft with an estimated error of 0.02 ft. The single zenith angle is read as The estimated errors in instrument and target centering are 0.003 ft. If the elevation of the occupied benchmark is 632.27 ft, what is the corrected benchmark elevation on the island? (Assume that the instrument does not correct for Earth curvature and refraction.) What is the estimated error in the computed benchmark elevation if the instrument has a DIN 18723 stated accuracy of +-3"?
From the given data of differential leveling as shown in the tabulation: Find the difference in elevation of station 7 and station 5: pls answer in complete solution. pls answer in 2 DECIMAL PLACES
Which type of leveling is more accurate? Profile leveling, differential leveling, reciprocal leveling, trigonometric leveling
A level loop was run and the raw elevations in Table 2 were calculated based on backsights and foresights. A plan view of the loop is shown in Figure 2. The true elevation of BM1 is 195.00 ft. Adjust the elevation of each station such that the error is evenly spaced. Show sample calculations of your work. Also determine the accuracy ratio of the survey. BM₁ 5 mi 3 mi BM2 BM4 3 mi BM3 4 mi Figure 2 Table 2 Station Raw Elevation [ft] BM1 195.0 BM2 205.6 BM3 209.8 BM4 204.7 BM1 195.5
Solve the given problem. Thank you
Survey