5. Fig. P2.5 shows an arrangement of conductors for a 1 phase supply, the current being equally divided between conductors a and a' and between conductors b and b'. If the diameter of each conductor is 8 mm find the inductance per km of the line. [Ans. 1.54 mHJ 20 cm- 100 cm 20 cm| Conductor A Conductor B Fig. P2.5

5. Fig. P2.5 shows an arrangement of conductors for a 1 phase supply, the current being equally divided between conductors a and a' and between conductors b and b'. If the diameter of each conductor is 8 mm find the inductance per km of the line. [Ans. 1.54 mHJ 20 cm- 100 cm 20 cm| Conductor A Conductor B Fig. P2.5

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.31P: Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in...

See similar textbooks

Similar questions

Consider a 3-phase, 50 HZ, 11 KV distribution system. Each of conductors is suspended by an insulator string having two identical porcelain insulators. The self-capacitance of the insulator is 5 times the shunt capacitance between link and ground. Find the voltages across two insulators.
I need the answer as soon as possible
Over sting of 3- phase tran smission line has 4 insulators and Ce=0.15C. If the voltage between the steel pin of the first insulator and the conductor is 25 kV. Find 1- Thevoliage distribution over the sting and what witt be the string efficieney. 2- If the string is supplied by a guard ring and this lead to add one air capacitance of 0.12C. find the new voltage distribution and the efficiency
50 Hz, 11 kV Consider a three-core, three-phase, cable whose conductors are denoted as R, Y and B in the figure. The inter-phase capacitance (C₁) between each pair of conductors is 0.2 µF and the capacitance between each line conductor and the sheath is 0.4 μF. The per-phase charging current is C₁ (B) C₂ C₂: (R HH C₁₂ C₁ C₂ Outer sheath
Consider a three-core, three-phase, 50 Hz, 11 kV cable whose conductors are denoted as R, Y and B in the figure. The inter-phase capacitance (C₁) between each pair of conductors is 0.2 µF and the capacitance between each line conductor and the sheath is 0.4 µF. The per-phase charging current is C₂ HE C₁ ,C₁ Outer Sheath
Over sting of 3- phase tran smission line has 4 insulators and Ce=0.15C. If the voltage between the steel pin of the first insulator and the conductor is 25 kV. Find 1- The voltage distribution over the sting and what will be the string efficiency. 2- If the string issslisd by a cuardsing and this lead t de air capacitance of Lize ind the new voltave distribution and the efficienley
Solve this 2 problem in detail
1.1 Given the circuit in Figure 1, using Kirchoffs voliage law show that: jwME, Ez R1 + jwl1 R, R Figure 1 1.2 A ferromagnetic ring of cross-sectional area 800 mm and of mean radius 170 mm has two windings connected in series, one of 500 turns and one of 700 turns. If the relative permeability is 1200, calcula:e the self-inductance of each coil and the mutual inductance of each assuming that there is no flux leakage.
Q. 7
A 33 kV, 50 Hz. 3-phase underground cable, 6 km long uses three single core cables. Each of the conductor has a diameter of 2.75 cm and the radial thickness of insulation is 0.4 cm. Determine (1) capacitance of the cable/phase (ii) charging current/phase (iii) total charging KVAR. The relative permittivity of insulation is 3.
3. Find the capacitance per unit length of the single-phase line shown below. Conductors a, b, c are of 0.2 cm radius, and conductors d and e are of 0.4 cm radius. Oa 4m Oe 6ide X Side Y
i) Calculate V1 and V2 for the voltage across the string insulator having phase voltage of 33kV for transmission line using details tabulated in the Table 3(a). Table 3(a) Type of Insulator Shunt Capacitance between each unit 0.1 C String to junction Self -Capacitance of each insulator ii) With the help of a suitable schematic diagram and necessary theoretical explanation, illustrate how to improve the efficiency of the suspension insulator.