42) Acylinder 4 m diameter and m long retains water on one Side flhe ylinder is Supporteed as Shown in Fig Delermine the horizontal reachion at A and the vertical reaction af the cyinder Cuerght 169.2 KN . To

Q: Calcdate Sefe aergnt liquid hauint valume m3 and wight°5o KN

A: Given data : Weight (W)=50 KNVolume(V)=7 m3

Q: Cone 6 m in 1o em tylín- Jev 6 cm X

A: The CG of composite geometry can be determined by resolving the geometry into known shape such as…

Q: Find the ratio of the system.r, and r₂ for m₁ = m₂ = 1 kg, k₁= 2000 N/m and k₂ = 6000 N/m Base k₁ k₂…

A: To find: The ratio of the system. Given: The masses are m1=m2=1 kg. The spring constant are k1=2000…

Q: The dam in in the shape of a quarter circle is 100 m and has a radius of 25 m. (a)Determine the…

A:

Q: The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel. The is…

A: Given, width of rectangular panel, w=4m height of rectangular panel, h=3m depth of the rectangular…

Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method. 3m…

A:

Q: A rectangular scow 1 m long, 7.2 m wide and 2.4 m high has its center of gravity 1.5 m above the…

A:

Q: Q2:- The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel.…

A: Hydrostatic Force On The Plane Is Given By  FH=Pavg×Area Where Pavg Is Given By Pavg=ρghcPavg=ρgh2

Q: Caleulate the magnitude 4 direation of foree exerted on the three-quar ter cylinder (ABCD), shown in…

A:

Q: Derive the formula that gives the ressure a3Sociated with the depth for ne case where the spesific…

A:

Q: If a 9-kg steel plate is attached to one end of a 0.1 m x 0.3 m x 1.20 m wooden pole, what is the…

A:

Q: A Cylnder of Im n diamder is made with material of relative donsity o5. It is moored in fresh water…

A:

Q: Guren : H20 Reclangular lom Sabmenged object nodth w= Im of 45° Reguered: F= hydrostatic force YR -…

A:

Q: ne area of 5,700m2, with its longitudinal centre mine the new draughts forward and aft if a wei, d…

A: according to questiond2 ∂2udx2=∂2∂t2,0<x<L,t>0since the string  is of limited length and it…

Q: As shown in Fig. (3), determine the submerged depth of concrete cylinder (h), for equilibrium the…

A:

Q: Determine the magnitude of the hydrostatic force acting on the gate using the HYDROSTATIC PANEL…

A:

Q: 1.2 m 0-3m Osm. 2.2m Q. locate the Centroid Por the following areas:

A:

Q: The 3 × 4-m side of an open tank is hinged at its bottom A and is held in place by a thin rod BC.…

A: Given that the area of the plate AB is 12 m2 Let the tension ‘T’ in the rod BC, Now, make a Free…

Q: A vertical bulkhead has a door 3m high and 2m wide fastened by two hinges A and B as shown and is…

A: Solution Given data- Area - 3m and 2 m

Q: The t'ank shoun is filles with water, Af wheet depth does the resultant force act? The Surface under…

A:

Q: Consider the given image. Assume h-16 ft. L-71, 8-8.5 ft. The plate width is 5 ft. Hinge Pa Seawater…

A: Given the dimensions of the plate.  Required: Centre of pressure.

Q: Q//ron cube immersed in water Totel surface area 36 m tinds the buoyane force f the cubdD

A: Given data Surface area of cube = 36 m2

Q: If the square gate (refer to No. 6 Practice Problem') is replaced by a circular- shaped gate as…

A:

Q: deilling fluid or drilling mud density 863 26/9allan. dePth- to00 ft + ConVert reading to Water…

A: Given     Density = 8.63 lb / gallon  Find    Density interns of lb / ft3, psi / ft, and SG

Q: 22/A water tank with diame ter = 10 m thickness 8 mm %3D Max. Stress min. stress = 25 MPa of water =…

A: Write the formula for the pressure acting on the bottom of the tank. P=ρgh Here, P is the pressure…

Q: The rectangular panel, which is 4 m wide, 3 m high block the end of a 3 m deep water channel. The…

A: Given, width of the rectangular panel , B = 4m Height of the rectangular panel , H = 4m Height of…

Q: al Banrallng Mament

A: To Find: (a) Shear Force at each point. (b) Bending Moment at each point.

Q: A cylindrical tank 3 m in diamter and 6 m tall has a wall thickness of 15 mm. The tank is filled…

A: Diameter of the cylindrical tank (D) = 3 mHeight of the cylindrical tank (H) = 6 mWall thickness (t)…

Q: The 3 x 4-m side AB of a tank is hingrd at its hottom A and is beld in place by a thin rod BC. The…

A:

Q: malic Lide gate that is 4 ft wide and 3 ft highi. The gale is by hinges located along its top cdge…

A: Given Data:-Gate width=4 ftGate height=3 fth=6 ftd=9 ftSalt water specific weight r=64 lb/ft3

Q: One end of a rod of length L and density p is fixed by a frictionless pivot at a depth d under…

A: GIVEN; *Lenght of Rod=L *Density of Rod=ρ TO FIND; Equillibrium position of the rod in terms of its…

Q: Compute the pressure at depth g 5.33 1m from free surface of water.

A: Given data : Depth=d Acceleration due to gravity=g Density of water=ρ   Required : Pressure

Q: Q1-The gate shown in fig.1 is in cquilbrium.Cempute W, negelecting the mass of the gate? 2m Hinge…

A:

Q: Smeok 1Her herwn to a Bering With Fig 6.2 is En d eun SE ffners Com Stkant K = ef o-75 m. If ke frem…

A:

Q: Q3 Cadculate the totoniaas st location of hinge (X) for the gate shawn belaw, for the gale to open.…

A: Write the expression for the height from the free water surface where the hydrostatic force acts on…

Q: Determine the total force in kN on a circular plate of diameter 1.5 m which is placed vertically in…

A: Diameter of circular plate, d = 1.5 m  Center of the plate from free surface of the water, h' = 2 m

Q: Draw the fallowing in cubic system :- (020) ,(222), (101) , (201) , (111)

A: Miller indices - It represent the nature of the plane all proportional to the reciprocal of the…

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.