4. If w-30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the following: a. Maximum bending stress b. Spacing of the bolts if the shear force resisted by each bolt is 30 kN (Hint: Maximum moment occurs at midspan; Maximum Shear is the highest magnitude in the shear diagram) 210 mm 24 mm 15 mm 230 mm L 24 mm

4. If w-30 kN/m and L=10m, the cross section is made-up of two I-beams shown, determine the following: a. Maximum bending stress b. Spacing of the bolts if the shear force resisted by each bolt is 30 kN (Hint: Maximum moment occurs at midspan; Maximum Shear is the highest magnitude in the shear diagram) 210 mm 24 mm 15 mm 230 mm L 24 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 16-mm-diameter steel [E = 200 GPa] rod (2) is connected to a 50- mm-wide by 8-mm-thick rectangular aluminum [E = 70 GPa] bar (1), as shown in Figure PP5.3-2. Determine the force P required to stretch the assembly 3.00 mm. (1) 0.45 m Answer in kN rounded-off to 2 decimal places B 1.30 m Figure PP5.3-2 I
FN= 119, MN= 85, SN= 93
Calculate the stress in the steel of the section in PART B in MPa.0 and the ultimate moment capacity of the section in PART B in kN.m.0
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
i need the answer quickly
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
At a point 8ft from D, solve the shear stress 4in from the top of the cross-section. The cross section is 6in by 18in. 16 k 2 k/ft 8k 3 k/ft B -12 ft 8 ft-+9 ft- 12 ft +-9 ft- 4 ft 3 ft 3 ft O 16.46psi O 65.84psi O 8.23psi O 32.92psi
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
3. A solid steel shaft is loaded as shown in Fig. P-322. Using G = 83 GPa, determine the required diameter of the shaft if the shearing stress is limited to 60 MPa and the angle of rotation at the free end is not to exceed 4 degrees. 750 N-m 1200 N-m 2.5 m 2.5 m-
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are angle sections with the thickness shown in the figure. The working stresses are 70MPa for shear in the rivets and 140MPa for bearing stress due to the rivets. How many 22mm diameter rivets are required to fasten the following members to the gusset plate: (a) BC; and (b) BE? 000 4 m B с 96 kN D 6 m E 200 KN 4 m F G 4 m 96 kN H to- PBC - -14-mm-thick gusset plate -13-mm-thick angle 6-mm-thick angle PBE