4) The portion AB of the shaft shown in figure below has a cylindrical hollow cross-section with an outer diameter of d₁=30 mm and an inner diameter of d₂-24 mm. The rest of shaft is solid. The diameters of portion BC and CD are d₁-30 mm and d3=20 mm, respectively. The applied torques are T₁-80 N-m and T₂=140N-m. Determine (a) the reactions for the circular stepped shaft shown below, and (b) plot the angle of twist diagram for the shaft along its length. Take G-80 MPa. 100 mm B 90 mm 7₂ C * -20 mm 160 mm

4) The portion AB of the shaft shown in figure below has a cylindrical hollow cross-section with an outer diameter of d₁=30 mm and an inner diameter of d₂-24 mm. The rest of shaft is solid. The diameters of portion BC and CD are d₁-30 mm and d3=20 mm, respectively. The applied torques are T₁-80 N-m and T₂=140N-m. Determine (a) the reactions for the circular stepped shaft shown below, and (b) plot the angle of twist diagram for the shaft along its length. Take G-80 MPa. 100 mm B 90 mm 7₂ C * -20 mm 160 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7. Distributed Loads A beam supports a distributed load as shown. (a) Determine the equivalent concentrated load (b) Determine the reactions at the supports. wB = 4500 N/m WA = 1500 N/m %3D A -L 6 m-
Solve for Ay and By with FBD. (Please mention no.of reaction forces in supports for better understanding)
4. Part AB of the bar has a solid circular cross section and part BC has a hollow circular cross section. The bar is fixed at both ends and a 150-in-kip axial torque is applied at B. Suppose that you want to decrease the weight of the bar by increasing the inside diameter of part B. The bar is made of material that will safely support a pure shear stress of 10 ksi. Based on this criterion, what is the largest safe value of the inside diameter? 4 in 2 in 150 in-kip A -14 in 7 in
( Hand written and clean writing )
The central rod CD of the set below is heated from T1 = 30ºC to T2 = 180ºC by an electrical resistance. At the lowest temperature, the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel and each have a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Use EFe = 200 GPA, EAl = 70 GPA, αFe = 12 x 10-6 /°C, and αAl = 24 x 10-6 /°C. answer: 5.4 kN
The torques shown are exerted on pulleys A and B which are attached to solid circular shafts AB and BC. In order to reduce to total mass of the assembly, detemine the smallest diameter of shaft BC for which the largest shearing stress in the assembly is not increased. TA = 300 N m 30 min B TH = 400 N- m 46 nn
4.)show complete solution, final answer should be in two decimal only, i will automatically give upvote.
A long column such as the one depicted below loaded in compression initially along its axis has a tendency to rotate. Associated with that rotation the load P imparts tipping moments that are resisted by the springs. In the configuration below the springs are connected to the rod with a frictionless slider and remain perpendicular to the rod. The pivot at O is also frictionless, and the masses of the structure are negligible. P k L k (spring) Assume that the springs are at their happy (natural/unstretched) length when 0 = 0. (a) Let the spring constant k, the lengths b, L, and d be given parameters in the problem. Find the load load P as a function of the rotation angle 0 such that the system is in static equilibrium.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 8 mm and a length of L₁ = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 16 mm and a length of L₂ = 1.0 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 66 KN is applied to the rigid bar. L₁ A B Answer: 0₁ = i 38 02 i L2 (2) (1) (1) MPa MPa