#4 The beam is used to support a dead load of W k/ft, a live load of 2 k/ft and a concentrated live load of p Determine (a) the maximum positive (upward) reaction at A, (b) the maximum positive moment at C, and (c) the maximum positive shear just to the right of the support at A. Assume the support at A is a pin and B is a roller. 10 ft- A -10 ft C 10 ft- B 1 - Use 5 = 33 4 4₁ = P= W =

#4 The beam is used to support a dead load of W k/ft, a live load of 2 k/ft and a concentrated live load of p Determine (a) the maximum positive (upward) reaction at A, (b) the maximum positive moment at C, and (c) the maximum positive shear just to the right of the support at A. Assume the support at A is a pin and B is a roller. 10 ft- A -10 ft C 10 ft- B 1 - Use 5 = 33 4 4₁ = P= W =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: Suppose we have a uniform beam that is 4.00 metres long has a flexural rigidity of 27510Nm². N Find…

A: Load f(x) = 8.96(x+1.12)(4.92-x) Flexural rigidity, EI= 27510 Nm2

Q: 1. Solve for general and particular solution using homogeneous. (y? + 7xy + 16x?)dx + x² dy = 0 x =…

Q: For the beam and loading shown, determine (a) the equation of the elastic curve, and (b) the…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: r the beam and loading shown, use the double-integration method to determine (a) the equation of the…

A: To find maximum deflection and it's location

Q: A 7.6m cantilever beam shown carries 104KN/m uniform load. Point A is free end while point B is…

A: Objective: To determine the value of EIy' (kN/m2) at the free end i.e., A using the Double…

Q: The beam has a pin support at A and a roller support at B and is subjected to the loading shown.…

A: Given:Required:Maximum deflection

Q: Find the coefficient of friction if normal force is 1000 N and friction force is 555 N

Q: I do not understand these, please explain each one and the differences:Conjugate-beam method, double…

A: Properties of Conjugate BeamThe length of a conjugate beam is always equal to the length of the…

Q: A composite beam is fabricated by bolting two 2-in.-wide by 12-in.-deep timber planks to the sides…

Q: Integration of Rational Functions dx 9. S x²-4 10. S²-1 5x-1 dx

Q: If sin A 4/5, A in quadrant II, sin B = 7/25, B in quadrant I, find sin (A + B)

A: Given Data:sin A =4/5sin B=7/25

Concept explainers

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.

Question

100%

Please Solve this problem using Muller- Breslau principle.. thank you ( Step by Step solution )

#4
The beam is used to support a dead load of W k/ft,
a live load of 2 k/ft and a concentrated live load of p
Determine (a) the maximum positive (upward) reaction
at A, (b) the maximum positive moment at C, and (c) the
maximum positive shear just to the right of the support
at A. Assume the support at A is a pin and B is a roller.
10 ft-
A
-10 ft·
C
-10 ft-
B
4₁
Use
4₁ =
P =
W =
5
33
сл
4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(3) The beam supports a uniform dead load of 6 kN/m, a live load of 20 kN/m, and a single live concentrated force of 40 kN. Determine (a) the maximum positive moment at C, and (b) the maximum positive shear just to the right of the support at A. Assume A is a roller and B is a pin. -3m- -2m- B
The compound girder shown in the figure below is subjected to a uniform live load of 12 kN/m, a uniform dead load of 4 kN/m, and a concentrated live force of 38 kN. Determine (a) the maximum reactions at supports, and (b) the maximum negative shear and moment at point D. A 20'- B hinge C 8 10'- E 10-
The beam supports a uniform dead load of 500 lb>ft and a single live concentrated force of 5 k. Determine (a) the maximum negative moment at E, and (b) the maximum positive shear at E. Assume the support at D is a pin, A and C are rollers, and B is a pin. A B C D E -9 ft- -9 ft- -9 ft- 06 PROB 023 -9 ft-
The compound beam is pin supported at C and supported by a roller at A and B. Note that there is a hinge at D. Find the reactions at the supports. Neglecting the thickness of the beam. (Provide the whole solution along with its FBD)
Determine the horizontal reaction in kips at the connection A of the gable frame. Assume that A, B, and C are pin connections. The purlin loads such as D and E are applied perpendicular to the center line of each girder.
Complete sol. ty
1. The beam is used to support a dead load of 0.6 k/ft, a live load of 2 k/ft and a concentrated live load of 8 k. Determine (a) the maximum positive reaction at A, (b) the maximum positive moment at C, and (c) the maximum positive shear just to the right of the support at A. Assume the support A is a pin and B is a roller. A B 10 ft- 10 ft- - 10 ft -5 ft-
Please solve using muller bresalu method. Thank you
The dead load on the bridge girder is 800 N/m and the live load is shown below. Assume B and D are pins. Determine: The maximum positive reaction at B, The maximum positive moment at C The maximum negative shear at C only HANDWRITTEN answer needed ( NOT TYPED)
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the tension at wire BD. E 4 m 3 m 2 m 2 m O 1.95kN O 1.64kN O 0.91kN O 1.29KN o o oO
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
show complete solution, i will automatically give upvote.