3kN2revd+6mmd600mm150mm1-Which section have max shear *2-shear in section 2 is3- om is equal to5- d in section 1 is *

Maximum shear stress Shear stress, often denoted by τ (Greek: tau), is the component of stress…

Answered: 3kN 2 rev d+6mm d 600mm 150mm 1-Which…

Engineering

Mechanical Engineering

3kN 2 rev d+6mm d 600mm 150mm 1-Which section have max shear

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Needs Complete typed solution with 100% accuracy.
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
60 k Timet 30 kN DROW the sheaR and mament Im diagram with complete soktion
3- Draw the shear force and bending moment of the beam. You have to find their equation, and your diagram without calculation is not acceptable.(41) 20 kN 1.5 kN/m B 1m 1 m 4 m
FIGURE PS-66 500 N/m 0.60 m 1 Compute tbe reactions at the supports using the toch niques shown in Section 5-2, 2 Draw the complete shearing force and bending noment dagrams using the techniques shown in Sections 5-3 through 5-8, 3. Determine the magnitude and location of the maximum absolute value of the shearing force and bending moment
6
asap pls
• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft • Briefly describe which type of shaft is more effective. • See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page.
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
Which set of compatibility equations matches the following torsion members connected end-to-end in series? 30 in. O || = C a 560 8₁ a & + gap 05/0 18 in. 6 in. (2) 0 & + ₂ = 0 О ф, = фг 0 8₁ = 8₂ - 8₂ 04+₂=0 & + ₂ = constant Ta (3) 8₁ + gap = 8₂ &₁ = & + gap D. & + ₂ = constant 8 in. (2)
6.21-6.38 For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Neglect the weight of the beam.
load (KN) Elongationc PAL 0.5 3-8 7-9 12-9 14-3 15-9 16.9 17-8 19.1 21-2 24-2 26-9 30 32.0 NO S a. 1 0-3 0-5 0-7 0-9 1 1-1 11-3 1-6 1-9 n(mm) 2-2 2-5 28 calculation -compression Stress (6c) = A compression strain (c) = Lo-Lf Lo -young's Modulus (E)=0C Ec hight = 6-8 mm. d = 5.9 mm.