3.6 m y A2 = 1,384 mm^2 A3 = 536 mm^3 F A (1) 2.4 m Rigid bar B (2) E 1.8 m (3) D X 3.0 m The assembly shown consists of a rigid bar ABC, two fiber-reinforced plastic (FRP) rods (1) and (3), and FRP post (2). The modulus of elasticity for the FRP is E- 16 GPa. Determine the vertical displacement of joint D relative to its initial position after the 34 kN load is applied to the nearest.1mm. A1 = 500 mm^2

3.6 m y A2 = 1,384 mm^2 A3 = 536 mm^3 F A (1) 2.4 m Rigid bar B (2) E 1.8 m (3) D X 3.0 m The assembly shown consists of a rigid bar ABC, two fiber-reinforced plastic (FRP) rods (1) and (3), and FRP post (2). The modulus of elasticity for the FRP is E- 16 GPa. Determine the vertical displacement of joint D relative to its initial position after the 34 kN load is applied to the nearest.1mm. A1 = 500 mm^2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Plzzzz
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Solve it on priority
Using the force (flexibility/compatibility) method, analyse the structure in the figure below:
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
Consider the truss shown in (Figure 1). Suppose that F = 12 kN. gure B C D 12 m, 6 @ 2 m E F 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FCJ = Submit __ Part C μA Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Value Units Request Answer ? Units ? Determine the force in member KJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
Fundamental Deformable Bodies
In the given system rod lengths are LAB = 5m, LBc=3m and the angle attached to the horizontal of the AB rod is a = 37°. The cross- sectional areas of the rods are A = 15 cm’and Anc = 20 cm and the modulus of elasticities of the rods are E=80 GPa and EBc=100 GPa LAB , A AB Luc, Apc В C a) Calculate the stresses that will occur in the bars. 20 kN b) Calculate the horizontal and vertical displacement at point B.
Read the question carefully and give me both right solutions with clear explanation. Don't copy from other websites solution