3. The plate as shown weighing 25 kN is raised by a cable sling. The cable sling has the identical clevis at each end and the pins through these clevises are 20 mm Ø. Determine the shear stress in the pin. Compute the bearing stress between the clevis and the pin if the thickness of the yoke is 25 mm. Use 2 decimal places in every solved value. (* p,-.

3. The plate as shown weighing 25 kN is raised by a cable sling. The cable sling has the identical clevis at each end and the pins through these clevises are 20 mm Ø. Determine the shear stress in the pin. Compute the bearing stress between the clevis and the pin if the thickness of the yoke is 25 mm. Use 2 decimal places in every solved value. (* p,-.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The lower ends of the three bars are at the same level before the uniform rigid block weighing 40 kips is attached. Each steel bar has a length of 3 ft, and area of 1.0 in2, and E = 29 x 106 psi. For the bronze bar, the are is 1.5 in2 and E = 12 x 106 psi. Determine: (a) the length of the bronze bar so that the load on each steer bar is twice the load on the bronze bar. (b) the length of the bronze that will make the steel stress twice the bronze stress.
Problem 4 The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress is Tult = 370 MPa and a bearing stress ultimate is 400 MPa. Use a factor of safety for shear of F.S =2.5. Thickness of the plate is 13mm. 30 mm 80 kN 30 mm 40 kN 40 kN
1) will upvote anyone who will answer correctly. thanks
Assume that the clamp shown has been tightened on wooden planks being glued together until P = 420 N. Determine the stress in A and D Find the location of the neutral axis
Solve fast I will upvote
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! For the frame shown, a 4QQT-N load is acting on member ABD at D. If the allowable material shear stress for is 4Q MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the bearing stress developedalong the plane ABC.Answer: σb ___________________
Need asap pls. Thanks.
1. Answer Set A only
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Answer the letter e only
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.