3. For the planar wedge shown below:22 mSlip surface39° 28°Calculate the factor of safety against plane failure assuming:9 (degree) 7 (kN/m³)c (kPa)4)5026001950c: cohesion of rock mass; y: unit weight of rock mass; q: friction angle of rock mass11

Answered: Image /qna-images/answer/33f7d17e-cdc3-43d8-b37c-3b7dccf124c6.jpg

Answered: 3. For the planar wedge shown below: 22…

3. For the planar wedge shown below: 22 m Slip surface 39° 28° Calculate the factor of safety against plane failure assuming: 9 (degree) > (kN/m³) c (kPa) 2600 1950 cio ۔۔ 50 maga

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. Point A lies in a clayey sand layer with ' = 38, c' = 10 kPa, and Ko = 0.5. The ground surface is…

Q: eights was pressed into soft clay in a borehole. The torque was applied and gradually increased to…

A: Using relation :s=TπD2H2+D36

Q: What is the factor of safety of the slope of a copper open pit mine excavated in a rock mass having…

Q: Use the stress-strain curve, where shear stress and strain response are obtained at different…

A: Detailed solution is provided belowPlease read carefullyThank you. Explanation:Step 1:Step 2: Step…

Q: 85 kN/m2 25 kN/m2 Try solving the following problem: Practice Problem 1: (Repeat practice problem…

A: Given data σx = -45 KN/m2 σy = -85 KN/m2 τxy = τyx = -25 KN/m2 θ = 90° - 40° = 60° (plane AB make…

Q: Problem 9: For the state of a certain soil stress shown, maximum shear stress. Express your answer…

Q: An embankment load of 500 kg/cm²

Q: Following Newmark's method, calculate average stresses at the bottom and the top of the clay…

A: q= 100Kn/m2unit weight of clay = 18.5 kN/m3w=22%

Q: Determine the moment magnitude in a place where the length of the rupture was 550km, the slip was 2m…

Q: Laboratory Problem Exercise #2 Given the figure and the following data: Determine (a) the width of…

A: Given:- The unit weight of the concrete, γc=2.4 T/m3 The coefficient of friction between the base…

Q: a. Maximum and minimum principal stresses b. Normal and shear stresses on plane AB' d

Q: The location of trial failure surface on a slope is shown in Figure and the stress components for…

A: Driving stress: The summation of all the shearing components with respect to the slice number is…

Q: find out the total area of rupture on the fault; 1011

Q: Problem-Shear strength A vane of 12 cm long and 10 cm diameter was pressed into deep soft clay at…

A: Given data- Length/Height of the vane H=12 cm, Diameter D=10 cm, Torque T=50 N-m, To Find- The…

Q: A wheel load (force) of 3000 lb. is applied directly to a crushed rock base to an unknown depth h.…

Q: A soil profile is shown in Figure 7.28. An embankment load of 500 kg/cm² is placed on the ground…

A: Given data h = 26ft p = 500kg/cm2 first change the units: 500X2048 = 1.06 X 106lb/ft2

Q: The excavation was being done for a foundation trench in a plastic clay having a unit weight of 2.3…

A: Plastic clay- unit weight γ=2.3 gm/ccDepth of excavation Hc=4 m,ϕ=0o

Q: - B=10m q= 400 kN/m² 2 m- sand 10 m- clay

Q: 6. Calculate the effective vertical stress at 10m depth assuming y, = 26.5 kn/m³and that the soil…

A: solution attached in next step

Q: SITUATION 2: The water table in soil deposit is 1 m below the ground surface. The soil above the…

Q: Determine the shear stress at points A, B, C and D for the following section. Also determine the…

A: Given V=10KN To find shear stress at point A,B,C and D

Q: n 18 kg. slab slides down a 15 degrees inclined plane on a 3 mm. thick film f SAE oil at 20°C. The…

Q: ertical and in recent.

A: According to given dataDepth of zone = 500m

Q: sample of dry soil is subject to a nd is found to have an angle of f o 29° and a minor principal…

Q: al a Q2/ Calculate the vertical stress in a soil mass depth of 5m vertically below a point load of…

Q: 2 m Ydry = 14 kN/m³ GWT Sand 4 m Ysat = 18 kN/m³3 Ysat = 19 kN/m³3 .5 m Clay Void ratio, e = 0 LL =…

A: To find the settlement of the clay layer-

Q: Factor of safety of the slope for which the other information is given in the Figure is (0,5+b).…

A: Factor of safety of the slope is (0,5+b) Where, b = (1,5) Axial deformation is measured at the…

Q: 9:25 PM docs.google.com/forms/d/e/l B) From the given formation of soil, the water table is located…

Q: Soil with a unit weight of 20 kN/m3 is excavated at 3m below the ground surface. Calculate the shear…

Q: A cut slope was excavated in sand. The slope is shown in following attachment .

A: According to lacey silt is kept in suspension by the vertical component of eddies which are…

Q: A building is founded on a rectangular mat of dimensions 20 m x 10 m as shown in the plan view in…

A: The increase in vertical total stress at a depth of 5 m below the lower rightmost corner of the…

Q: Given the state of in situ stress below 15 0 lo] = 0 40 in MPa 0 0 Where z axis is vertical and xy…

A: a) from Andersonian faulting classification system We observed that vertical forces is minimum as…

Q: Q2: For the soil element shown in the figure. Draw Mohr circle, locate OP (origin point), then find…

A: Soi classification can be done by many methods and it is having many types of soil like clayey,…

Q: 100 kN point loạd and 40 kN/m line load are applied on the ground. surface as shown. Compute the…

Q: In a direct shear test on sand (C = 0), area of circular box was 50 cm², normal load was 750 kN and…

A: C= 0 Area of circular box = 50 cm2Normal load = 750 kNFailure load = 460 kNTo Find : ?

Q: Solve

A: In a relaxed basin the failure plane does not intersect with drilling operation when a horizons well…

Q: 131.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 35 131.6 kPa 2. Find Normal and Shear Stress at Failure Plan…

Q: Regarding geotextiles used in separation, what is the required burst pressure of a geotextile…

A: Given, Maximum size of the stone, Da= 75 mm Tire inflation pressure, Pt=1000 kPa Cumulative…

Q: Find the maximum permissible height of water in the tank shown in Figure (1). Given that: Tank…

Q: Given the figure and the following data: Determine (a) the width of base b on the conditions: a.1…

A: Given The unit weight of the concrete = 2.4 T/m3 The coefficient of friction between the base and…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

3. For the planar wedge shown below:
22 m
Slip surface
39° 28°
Calculate the factor of safety against plane failure assuming:
9 (degree) 7 (kN/m³)
c (kPa)
4)
50
2600
1950
c: cohesion of rock mass; y: unit weight of rock mass; q: friction angle of rock mass
1
1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

8. Estimate the settlement of the center of the tank, shown in the sketch, due to consolidation of the 20-ft layer of clay. 80'diam. -Oil tank; 500 lb/sq ft 30' fine sand; 125 lb/cu ft 20'clay; qu = 1.3 tons/sq ft W = 54 % Wp = 26% W = 44% Isat = /15 lb /cu ft %3D Rock %3D %3D
Q#4: Plate load test performed on a uniform deposit of sand and the following observations were recorded. The size of the plate was 45cm x 45cm. Plot the Pressure-Settlement Curve and determine the safe load on a footing 2m x 2m if the settlement is not to exceed 40mm. Pressure (kPa) 2 4 8 12 16 24 Settlement (mm) 3 6 20 40 60 100 Note: Write the proper answer in word format Subject: Geotechnical Design
Soil mechanics Geotechnical Engineer. Please solve in clear writing With sincere thanks and appreciation
Q36 Please provide justified answer asap to get a upvote
A 10 m high sope of dry clay sol (unil weight = 20 N/m) with a slope angle of 45 and the circular slip suriace, is shown in the figure (not drawn to the scale). The weight of the slp wedge is denoted by W. The undrained unt cohosion (C) is 60 kPa. 10m Unit weight= 20 kN m C = 60 kPa 10m 448m, 45% The facter of safety of the slooe against sip failure. IS
Calculate the geostatic stress at point A, the soil unit wieght is 18 kN/m3. 6 m 1.6 m 3 m •A 1.5 m PLAN 6 m Vertical load 50 kN/m2 3 m SECTION Select one: O a. 24 kN/m2 o b. 44 kN/m2 OC 54 kN/m2 o d. 45 kN/m2
A square footing is loaded as shown in Figure 05.13. The center of the base of footing is at coordinate (0, 0, 0). Determine the increase in vertical stress at a point whose coordinate is (3, 0, 4) using pressure isobars based on Boussinesq equation for square footings shown in Figure 05.7. O O O 10.215 O 10.512 10.125 10.251 P = 900 KN #7 2 m Figure 05.13
o T ☺ ť (Q4): For the soil profile shown in figure (2) find the difference in stress in (kPa) at point located at a depth (10m) under the center of the circular foundation when using the below formulas and when using the approximation method 1 Ao, = q [(R/2)* + 1] Dia4m q0.21 N/mm N.G.S Sand e0.8 G.-2.6 3m W.L e0.7 G-2.7 5m Clayey - Sand e045 G.-2.68 مر ر ل لأعلى لاستعراض الفلاتر إضافة شرح. .. mum < II
The following data were obtained in a direct shear test. Normal pressure =20kN/m 2 , shear stress on the failure plane =16kN/m 2 . Angle of internal friction =20 ∘ , cohesion =8kN/m2. Represent the data by Mohr's Circle (by plotting) and show the principal stresses and the direction of the principal planes on the plot
2.) Using the principles of Mohrs circle, for the soil element s shown, determine the following. a) Mayimum principal stress b) Minimum principal stress C) Novmal Streas on plane AB d) Tangential Stress on plane AB 1ookPa B 25kPa 45° 25KPG 15 450
An embankment is shown in the figure. Determine the stress increase (in kPa) under the embankment at points A₁ at a depth of 8m and A₂ at a depth 4m. 4o = alt (B₁ + B₂ + -14 m- (az) B₂ -11.5 m -5 m- H=7m -14 m- [y-17 kN/m² -16.5 m-