#3 The beam is subjected to a uniform dead load of 1.2 kN/m and a single live load of P kN. Determine (a) the maximum moment created by these loads at C, and (b) the maximum positive shear at C. Assume A is a pin. and B is a roller. A F 6 m P B Use 4₁ = 5 P = 3

Q: e of water in the reservoir. The numbers on the plot show the horizontal distances (m) which were…

A:

Q: 2.A hydrographic survey of a lake generated the following approximate measurements: 16,500 sq m =…

A:

Q: 1. Three streams flow towards Matuno River. The watersheds through which the water flows have…

A: Chemical mixing Formulae for two or more mixing

Q: Problem 5 Angles AOB, BOC, and COD are measured on the same angle at point O. Determine the most…

A: GIVEN : Measurement of Angles, number of measurements. REQUIRED : Most probable Angle, MPV

Q: Q.2. Please calculate the elevations of every station given in the table and show the arithmetic…

A: It is required to determine the height of instrument. It is required to determine the elevation.

Q: Calculate the area (in sqm) of the cross-section of ranges DF. (Type your answer using 2 decimal…

A: To determine Area of section Df

Q: ns 1 and 2. Locate the centroid of the shaded area

A:

Q: Find the resultant vector, T , given the diagram below. Round your answer to 1 decimal place. SHOW…

A:

Q: Find the forces (kN) on the members of the given truss. Determine also the magnitudes of the support…

A:

Q: Mass curve the relation between? A- Rain mass and depth. B- Rain height and depth. C- Rain depth and…

A: finding out the mass curve relation.

Q: Calculate the coordinates of a foresight point P101 using the following data: Occupied point O: N…

A: Point O BS=0.45 m HI=144 m FS=- Elevation=143.55 m Azimuth=285 degree Distance=35.3 m Point A BS=-…

Q: Define Normal or Gaussian Distribution

A: It is defined as a continuous probability distribution that is symmetrical about the mean. it is…

Q: Completely fill up the missing data ((marked with "X") and apply arithmetical check STA BMa 0+00…

A: Given: Station BS HI FS IFS Elevation (m) BMa 0.987       120.895 0+00       1.243   0+10…

Q: Q.2. check. If there is an error please distribute it to the elevations. E = 40* K Please calculate…

A: Levelling is the procedure of comparing heights of points on the surface of earth. It is important…

Q: Latitude and Departure equations will never return positive values. False True

A: False

Q: Solve and show complete solution. From the technical description below, what is the coordinates of…

A:

Q: please calculat the angles and complete the following table. Ba A 零方向 Survey Survey Targe Reading…

A: ANSWER:-

Q: Q2The areas within the contour lines at the site as follows: Calculate the volume of water between…

A: Given Above contours and the area between them

Q: 15-min counts (рси) 150 (kph) 60 38 62 375 55 56 405 175 215 5 42 660 278 51 12 315 300 55 57 22 340…

A:

Q: Q2/. The areas within the contour lines at the site as follows: Calculate the volume of water…

A: Given that: Counters (m) 90 88 86 84 82 80 78 Areas (m2) 4760 4310 3770 2960 2190 1640 8400

Q: Q.2. O Please calculate the elevations of every station given in the table and show the arithmetic…

A: Height of instrument(H.I)=B.S+ Elevation Elevation of Reduce Level = H.I-I.S or H.I-F.S…

Q: Line AB = 250m long and was paced five times by the surveyor and recorded as follows:  Another line…

A: Formula used -  Totsl Distance = Pace factor ×Avergae of paces   For the first paced distance -  250…

Q: QI/ An complet traverse table is obtaind as flowing ? Calculate 1. length of DA & bearing of AB 2.…

A: Let the length of DA be x and bearing of AB be θ a.) line length RB    θ Latitude…

Q: As shown in the figure below, point A and point B are both sides of the river, but the point B…

A: Let the point C is observed opposite to point C. Draw the figure,

Q: B. 0.9m 900 N 0:6m 2.4 m 2000 N 0.6 1.8 1.8

A:

Q: Transform graphically the figure into one wherein the sides with unknown quantities are made…

A: Solution: Interpretation of Data: Line Bearing Length AB S 86°35' W 607.66 m BC S 31°35' W…

Q: From the measured values of distance AB, the following trials were recorded. DISTANCE (m) TRIALS 1 2…

A: Given,DistanceTrail      Distance 1.          120.682.           120.843.          120.764.…

Q: 1. Using the information below, determine the following azimuths. The image below is oriented so…

A:

Q: Q3: The polygon traverse ABCDEA shown in figure 2. is to be divided into two equal areas by a…

A:

Q: Find the x and y coordinates of the centroid shaded area. Integration is indicated to solve. 1. 4 ft…

A:

Q: On which theory the least squares method based?

A: Least square method adjustment:- To identify the most probable coordinates for connected…

Q: IIL Complete the horizontal angle measurement note Result Reviewer Sight Reading Angle Face to 11 A…

A:

Q: Refer to the figure. Where is the resultant located? 200KN 300KN 30° 60° 60° Oe. None of the above…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.