Please quickly +230 V3.57 A5.05 AVm Iio (t)0 a28.95 V40.95 Vis (t)100 V16.72 Ω66.88 ΩSvo(t)T100 V100 V45 02S1R- Vo(t) +S2Q. Calculate the RMS output current if the firing angle is 28⁰2πlo (t)3.61 A5.11 AwtQ. Determine the average value of volt if the firing angle, a is 35º. Note: Vm = 100 V.31.83 V57.91 VQ. Find the R value if the average output voltage of the rectifier is 57 W, and thefiring angle is 20⁰33.44 Ω133.76 Ω

In last question average output power is given not average output voltage since the unit of power is…

+ 230 V 3.57 A 5.05 A Vm I io (t) 0 a 28.95 V 40.95 V is (t) 100 V 16.72 Ω 66.88 Ω S vo(t) T 100 V 100 V 45 0 S1 R - Vo(t) + S2 Q. Calculate the RMS output current if the firing angle is 28⁰ 2π io (t) 3.61 A 5.11 A wt Q. Determine the average value of volt if the firing angle, a is 35º. Note: Vm = 100 V. 31.83 V 57.91 V Q. Find the R value if the average output voltage of the rectifier is 57 W, and the firing angle is 20⁰ 33.44 Ω 133.76 Ω

+ 230 V 3.57 A 5.05 A Vm I io (t) 0 a 28.95 V 40.95 V is (t) 100 V 16.72 Ω 66.88 Ω S vo(t) T 100 V 100 V 45 0 S1 R - Vo(t) + S2 Q. Calculate the RMS output current if the firing angle is 28⁰ 2π io (t) 3.61 A 5.11 A wt Q. Determine the average value of volt if the firing angle, a is 35º. Note: Vm = 100 V. 31.83 V 57.91 V Q. Find the R value if the average output voltage of the rectifier is 57 W, and the firing angle is 20⁰ 33.44 Ω 133.76 Ω

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer fast and short in 15 mint
a metal device box has four 12 AWG conductors, two internal clamps, and a duplex receptacle. Total voume ? Device boxsize ?
gn In/Sign Up OSign In/Sign Up 006157 Exam + >C合 assignments.pennfoster.com/Exams/Random?qNo3DqD5EpTNrP8E%3D boTax Exam Lesson Name: Advanced Grounding Applications Exam number: 006157RR Exam Guidelines > Exam Instructions Question 14 of 20 : Select the best answer for the question. 14. Which of the following statements about the neutral ground-strap ground fault protection system is correct? O A. It can be installed only at the main service equipment. O B. It monitors only the phase conductors. O C. It monitors the grounding electrode conductor at the utility connection. O D. It monitors the equipment grounding conductor and a single phase conductor. O Mark for review (Will be highlighted on the review page) > 111
8. Connect the Electronic VOM, set to the ammeter function on the 15mAdc range,between points A and D.9. Close switch S1. Measure current IAB. IAB = 19.5 mAdc 10. Measure current IAD flowing through resistor R1. IAD = 14.8 mAdcAre currents IAB and IAD entering or leaving point A? __________ Is the sum of currents IAB and IAD equal to total current IT? __________Is the current IAB entering or leaving a junction point B? __________
Each unit of a 100-unit hotel is 12 × 15 ft. In addition, there's a 60 × 20 ft officeWhat's the service demand load for conductor sizing for lighting and receptacles?
In a CE configuration, the voltage gain is __________ . a.always positive b.negative c.almost zero d.very low
10.a. When new work is being performed, an outlet box must have a minimum depth of A. 1 in. B. 1 1/2 in. C. 2 in. D. 2 1/2 in. 10.b. When new outlets are being added to the first floor of a two-story house with an unfinished basement, the easiest route for running cable is usually A. behind the wall. B. behind the baseboard. C. by way of the second floor. D. by way of the basement.
UP/DOWN CLK Qo Q₁ Q₂ Q4 (UP) (DOWN) _____ (UP) (DOWN) 山 In
what is the unique feature fore fire alarm system by arduino?
conduits are most suitable for house flats and offices.
10.A. Which of the following is required in each separate service disconnecting means?A. Grounding electrodeB. Service conductorC. Main bonding jumperD. Equipment grounding conductor10.B. When sizing an equipment bonding jumper on the load side of an overcurrent protective device, thesize of the conductor jumper is based on theA. current rating of the protective device.B. size of the feeder's equipment grounding conductor.C. size of the grounding electrode conductor.D. size of the conductors feeding the protective device.10.C. Grounding clamps are typically suitable for connecting how many conductors?A. OneB. ThreeC. FourD. Two
What is mean by equipment grounding and system grounding?