2) A generator having a rated current equal to 1000A is to be protected by a circulating current differential relay using a stabilizing relay. The through fault stability is required up to 10 times full load current. If the voltage across the relay is 25 V during fault, determine the required value of stabilizing resistance (consider stability factor = 3). The relay picks up at 0.1A and has a resistive burden of 50 ohms. %3D

2) A generator having a rated current equal to 1000A is to be protected by a circulating current differential relay using a stabilizing relay. The through fault stability is required up to 10 times full load current. If the voltage across the relay is 25 V during fault, determine the required value of stabilizing resistance (consider stability factor = 3). The relay picks up at 0.1A and has a resistive burden of 50 ohms. %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The capacitor acts like a/an ____ circuit when connected to a DC voltage or current source; _____ on a capacitor must be continuous and ____ might be discontinuous. (single answer)open, current, voltageclose, voltage, currentopen, voltage, currentopen, voltage, current
15. _______ is a proximity sensor that uses the principle of ‘eddy current’ to sense the presence of an object.
3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
Untitled form Your email address will be recorded when you submit this form. Not eng.refcon.k2324@sadiq.edu.iq? Switch account objective question(jW Jlgs) For the circuit shown below choose the correct answer V2 Vi SA 220 300 25A In 31
Question Completion Status: Click Submit to complete this assessment. Question 8 What do you do to an asynchronous counter to let it count froms14 to 0? (Handwriting solution is needed: include this in your pdf file) Click Submit to complete this asseESment,
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
Which of the following statements about equipment grounding conductors (EGCS) is true? A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor. B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray. C. No current should be present in the EGC during normal operation. D. EGCs are required to be decreased in size to address voltage drop.
The contractor is controlled by?
4. Do some search about the functionality of Airport Metal Detectors. Explain your answer in a paragraph.
Assuming all terminals are rated 75°C and you have a #10 AWG THHN/THWN conductors in a conduit and the conduit is run on the roof off a office building where the ambient temperature never rises above 30°C the largest size circuit breaker or fuse permitted to protect these wires is:?
The wording that I am running into with questions such as "The number of conductors required to be installed between three-way and four-way switches is " is confusing. The text is not expalining this in a way that I am understanding anything other than grounding conductor, which is optional unless I am using a metal box. So what type of "conductor" is beng discussed?
The only way to reach any of the levels where ABC Company is located in a building with ten stories is to use the elevator. In addition, those on the ninth and tenth levels need to connect to a group of servers located on the eighth. Describe the best wiring for the lift shaft. Pick the best option if there is more than one and justify your decision. If you think that interfloor connections may need to operate at substantially greater rates in the future, you may want to reconsider your current option. What is the optimum media for unbounded data transfer requirements? Justify your response.