14 T=625 Nm Antriebszapfen 27 A F-5,31 KN 135 Zapfen der Getriebewelle 25 B 12,5 FB = =4,69 KN A stepped shaft made of 25CrMo4 (Rm = 800 MPa, Rp0.2 = 450 MPa) is loaded by reversing bending and swelling torsion. The support figure is n = 1.21. Calculate for the shoulder at position "B" (R = 2 mm): a) the notch size factors αkь and Ɑkt for bending and torsion. b) the notch sensitivity factor nk c) the stress concentration factors ẞkb and ẞkt.

14 T=625 Nm Antriebszapfen 27 A F-5,31 KN 135 Zapfen der Getriebewelle 25 B 12,5 FB = =4,69 KN A stepped shaft made of 25CrMo4 (Rm = 800 MPa, Rp0.2 = 450 MPa) is loaded by reversing bending and swelling torsion. The support figure is n = 1.21. Calculate for the shoulder at position "B" (R = 2 mm): a) the notch size factors αkь and Ɑkt for bending and torsion. b) the notch sensitivity factor nk c) the stress concentration factors ẞkb and ẞkt.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Disadvantage of taper turning by compound rest method is that only hand feed is possible. Select one: O True False K HERE TO ACCESS FINAL EXAM MEEETING Jump to.. dfjoiner (8).pdf Type here to search
Solve it quickly please now
What’s the correct answer for this please?
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
a) Figure Q3a shows a stage 1 to stage 2 compound gear train through from Gears A, B, C to D. If the input shaft rotates at 1300 revolutions per minute (rpm), calculate the angular velocity (w) in rad/s at the output shaft of the compound gear train. See below for the number of teeth for Gears A, B, C & D. [10 marks] Gear A: 44 Teeth Gear B: 96 Teeth Gear C: 60 Teeth Gear D: 140 Teeth Gear B- -Stage 2 Gear A- Input shaft- Stage 1- Gear C- -Gear D -Intermediate shaft -Output shaft Figure Q3a b) A motor with a power rating of 3600 Watts is coupled to the input shaft of the pinion (or driver) Gear A as shown in Figure Q3a. Calculate the torque at the input shaft and at the output shaft. Assume no losses and 100% efficiency. [5 marks] c) Draw a typical indicator diagram of pressure versus volume (p-v) to illustrate the actual Otto cycle for a four-stroke reciprocating internal combustion [RIC] engine. Clearly label each part of the p-v indicator diagram and clearly indicate when the piston…
In crank and slotted lever quick return mechanism, the crank length is 161 mm and the distance between the fixed center is 286 mm. The length of the slotted lever is 586 mm. Determine the ration of time of cutting stroke to time of return stroke. Also calculate the length of the stroke .
Don't solve handwritten
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
Which of the following commands will move the tool in a diagonal line at a feed rate of 5 from position (10, 20), assuming absolute programming mode is active? Select one: a. N10G00X10F5 b. N10G01X20Y30F5 c. N10G01X10F5 d. N10G00X20Y30F5
Q1. The lathe operates on the principle of.. a. the cutter revolving against the work piece. b. the cutting tool, that can be controlled, can be moved vertically across the work piece_ c. the work piece rotating against the cutting tool, which can be controlled. d. both cutter and work piece rotating.
im sorry for the inconvinience , 500 d/d means 500 rpm. Its translated from turkish textbook , i forgot to translate the rpm value. Could you correct the substitutions please ?
10q In down milling, the workpiece is feed against the rotation of the milling cutter to produce a flat surface. Select one: True False