12.28 Consider a thin-walled circular pipe of mean radius a, loaded as a cantilever (Figure P12.28). Derive the following expressions for the membrane stresses: P sin 0 t at 0, =0 T. %3D =-. (P12.28) Px Cos 0. Ta't L- 2a

12.28 Consider a thin-walled circular pipe of mean radius a, loaded as a cantilever (Figure P12.28). Derive the following expressions for the membrane stresses: P sin 0 t at 0, =0 T. %3D =-. (P12.28) Px Cos 0. Ta't L- 2a

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM S5.1 A 12 m long steel pipe has an internal diameter of 80 mm and a wall thickness of 2.5 mm. Calculate the hoop and axial stresses when the pipe is used to transmit steam at a pressure of 10 MPa. [Ans. 160 MPa; 80 MPa]
1. A water tube boiler operates at 1100 psia has the following characteristics: No. of riser 100 Riser wall thickness 0.22 in OD of riser Length 3in 105 ft No. of 90° Bends 6 14 lb water / lb steam 1200 lb steam / hr-tube Circulation Ratio Steam per tube No. of Down Comer 1 Length of Down Comer 75 ft No. of 90° Bends 2 Calculate: a. The mean density b. Diameter of the Down-Comer for a 80 ft system height.
A spring subjected to torsional stress is made of hard-drawn brass wire. The ultimate strength in tension is 75,000 psi and the yield stress 26,000 psi. The modulus of elasticity is 14,000,000 psi. The load on the spring varies rapidly from 75 to 100 lb. What is the permissible design stress if the load is applied with minor shock? i ' ,
Explain briefly
ar,max section of 1.3 2.0 2.4 2.9 3.8 e maxim 4.6 7.0 15.3 he insulat 22.9 70.7 76.4 79.6 ✓ MPa; otube,max = ✓ MPa; vertical deflection of
ics Course Home
Compute Young's modulus, E, Poison's ratio, v, and bulk modulus, K, if Lame's first parameter, 1, and shear modulus, M, are equal to 24,000 and 16,000 MPa, respectively.
X24 \/\\\\\\\\\ Oxy = 9 X1 L 2H Figure 1: Cantilever beam. A cantilever beam of narrow rectangular cross-section of unit width is subjected to a constant shear stress, σry(x, H) = q, as shown in Fig. 1. (a) Derive the stresses using the Airy stress function = ax1x2+bx₁x² +cx₁x³+dx²+ex³, where a, b, c, d, e are constants. (b) Write the boundary conditions and use them to evaluate the constants. (c) Specify the boundary conditions needed for determining displacements. (d) Why do we not need higher order terms in o?
12:11 d a y O X O F 23%. Problem 1: A thin-walled cylindrical pressure vessel, 10 in. in mean diameter and 0.2 in. in wall thickness, contains an internal pressure of 1,500 psi. The ends of the pressure vessel are closed. An axial compressive force P of 10,000 lb. and a positive bending moment M of 10,000 lb-ft. are acting at the ends of the pressure vessel. strength of the pressure vessel material is 33,000 psi. The yield (a) Draw a stress element on the top and the bottom of the vertical diameter at the mid-length of the pressure vessel. (b) Draw a stress element on the front and the back of the horizontal diameter at the mid-length of the pressure vessel. (c) Check if yielding will occur at any of these four locations. Pressure P M M
.
8.7 A point-focus concentrating solar collector comprising a heliostat field and central receiver and a steam turbine-generator unit (refer to Figure 8.8) is operating under the following conditions: • Power plant electric power output Pa = 75 MW • Single heliostat surface area A, = 125 m? • Beam solar radiation flux incident on the heliostat IN = 835 W/m? • Heliostat-receiver concentration ratio C = 510 Efficiency of solar collector, that is, heliostat field and central receiver n = 0.69 • Efficiency of the power plant cycle and turbine-generator unit Nng = 0.36 • HTF in the receiver: molten salt (sodium potassium nitrates) with spe- cific heat e of 1.03 kJ/(kg K) • HTF temperature rises in the absorber/receiver from 298°C to 563°C, that is, AT, = 265 K Calculate (i) the overall (electrical) efficiency of the power plant, (ii) the rate of useful heat output of the central receiver/absorber, (iii) the total reflecting surface area of the heliostat field, (iv) the number of heliostats…