11.6 Draw the free body diagram for the arm ABC. A skeletal diagram of a hand holding a load is shown in the upper figure. If the load and the forearm have masses of 2 kg and 1.2 kg respectively, and their centers of mass are located at Gl and G2. The arm can be idealized as shown in the second figure. D G 75° B |G2 -135 mm- -100 mm- 65 mm

Q: F. 5N 5N 5N 10cm M. 7.5N 6.1cm 5.15cm 7.5N

A:

Q: Using a single acting cylinder work pieces are to be fed into a jig from gravity magazine. The…

A: In this system, a single acting cylinder is used to feed work pieces into a jig from a gravity…

Q: Write the sequential procedure for making the simple step turning operation for making the shown job…

A: The sequence for making the simple step turning operation for making the shown job: 1. Centering 2.…

Q: Q) Write introduction and conclusion for Lift Mechanism Bucket Boom Shoulder Mount Base

A: Write the introduction and conclusion for lift mechanism.

Q: Check stability  of truss Please be fast

A:

Q: 2) Write introduction and conclusion for Lift Mechanism Bucket Boom Shou Mou Base

A: Parts of lift mechanism is- Base Mount Boom Shoulder Bucket

Q: Select the reaction forces in a roller support. Horizontal Reaction Moment Reaction Vertical…

A:

Q: The angle of inclination of the plane at which the motion of the body is kept at its impending is…

A: Point of verge and sliding motion starts when body is placed on an inclined plane, the angle at…

Q: a. Carriage b. Tool post c. Compound rest d. Cross slide

A: Solution:

Q: -) Draw free hand and proportionate sketches for any four of the 1- Pan and rounded countersunk head…

A: Rivets are used for the fixing of two or more objects. Different types of rivets used in engineering…

Q: If a cylinder rod exerts 5,000 lb of force extending, how much force would a single lever toggle…

A:

Q: Multiple choice Which wheelbarrow shown is well designed

A: Given:

Q: Legs L1 and L2 must lie in the same plane as which other piece?

A:

Q: Finding support reactions

A: A loading forces are given. To determine, the reaction forces in both the supports.

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: Q) Write introduction and conclusion for Lift Mechanism

A: Given:

Q: Explain by drawing a figure the recovery or capsizing (overturning) situation of a boat in the water…

A: Capsizing when a boat or ship is turned on its side or it is upside down in the water then…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: What is the magnitude of the Right Reaction force in pounds?

A: GIVEN: F=1.5 kpis =1500 lbf TO FIND: The reaction on the right side. Rb

Q: 5. Static (angles are both 30°) 6. Static 7. Static attached to a post at an angle 8. Leaning…

A: Given All Mechanism or body is in a static condition which means a balanced condition.To findFBD…

Q: Determine the force in members AB, BC, and CE of the crane shown in Figure 3-1.

A:

Q: To decrease the amount of force needed increase the of the inclined plane. distance or length O…

A: Given Data⇒ Inclined plane

Q: QUESTION 10 A load of 6kN is supported as shown in the figure. The weight of the pulley is 2kN.…

A:

Q: Which among these joint consist of 3 degrees of freedom? a. Links and joints b. gripper c. wrist d.…

A: Degrees of freedom(DOF) can be expressed as the different ways in which a component can move. If a…

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: 0.75 in. 1'in. -20° 1.5 in.1 in. 3 in. 5 lb D 5 lb

A: Given,

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: What are the following: 1. Simple support 2. Roller support 3. Hinged pin support 4. Fixed support

A: 1) Simple support- it is a type of support in structure where a beam or member is supported…

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: Q 13. A frame is said to be 'Perfect frame, if it followS certain relation betvoen number of members…

A: Perfect frame will not change when it is subjected to load with help of perfect number of members…

Q: Q) Write introduction and conclusion for Lift Mechanism Bucket Boom Shoulder Mount Base

A: Write Introduction and conclusion for lift mechanism.

Q: Determine support reaction

A: This question can be solved by concept of static equilibrium.

Q: When facing, the compound rest maybe set 30° (to the cross-slide. If the compound rest is fed in…

A: Draw the diagram of the cross-slide and compound rest.

Q: 1- Draw three views of hexagonal nut for 24 mm diameter bolt according to rough rule dimension.

A: We can answer first question since the exact one is not specified. Please resubmit the question by…

Q: Draw free body diagram and kinetic diagram for Counterweight Box, Swing arm and sling please draw…

A: Given: A diagram of trebuchet To find: Free body diagram and kinetic diagram: Counterweight box…

Q: Create your own 2 problems about couple forces with complete solution

A: Given Couple forces To find 2 Problem with solution

Q: Facing is an operation to reduce the diameter of work piece. Select one: True False

A: False

Q: The short columns fail due to ________ Select one: a. Crushing

A: There are three types of columns, Long columns, intermediate columns and short columns.

Q: Use Method of Sections to find the forces in members CF & CD.

A: Given data Given truss system

Q: The work of the external forces that act on a rigid body as it moves from one position to another is…

A: Kinetic energy is defined as the energy associated with the movement of the body. So, when external…

Q: List three benefits of holding a workpiece between centers

A: A work holding technique is to hold the objects between the centers. One of the centers is mounted…

Q: The rolls are supported on bearings of side frames called *

A: The rolls are supported on bearings of side frames called Answer: Supports

Q: 600 lb FOR -6 ft -6 ft 7200 lb-ft 12 ft 150 lb/ft B

A:

Q: Define how to calculate the central angle of sliding slope in case of friction circle method?

A: A friction circle is a graphical tool that conveniently defines the course of action of the…