11. Given the specific gravity of oil is 0.85, what is its density in Kg/m^3?

Q: What is the magnitude of the resultant force of the two forces which are perpendicular to each…

A: Consider the given data A=20 unitsB=30 unitsθ=90o

Q: A load test on an 8mm diameter by 230mm long aluminum rod found that a tensile load of 5kN caused an…

A:

Q: Q2. A 40 mm diameter jet has a velocity of 25 m/s. Calculate the resultant force on a large flat…

A:

Q: Explain the words given below; a) fluid b) viscosity c) Newtonian and non-Newtonian fluid d)…

A:

Q: What is the property used to describe the pressure of the fluid?

A: Pressure of the fluid- It is defined as the force applied by the fluid per unit area.

Q: Figure shows a shear that is used to cut and trim electronic circuit board laminates. Draw a…

A: To find the degree of freedom and kinematic diagram-

Q: Problem # 3 a. What difference in temperature from standard if neglect in use of a steel tape an…

A: Given: a) L=50m ∆L=0.01m alpha=0.0000116 m/m-oC b) L=50m ∆L= -0.015m alpha=0.0000116m/m-oC   To find…

Q: Two cylindrical rods, one of steel and the other bronze are joined at C and restrained by rigid…

A:

Q: compressed gas tank was filled with either oxygen or helium but the lab technician cannot remember…

A: Given Volume of tank = 2ft³ Total filled weight = 20.3 lb Tank weight = 20 lb Pressure Gage reading…

Q: Calculate the elastic section modulus (cm³) of the cross-section about the horizontal axis. 200 12…

A:

Q: What pressure is required to reduce the volume of water by 0.60 percent If the volume modulus of…

A:

Q: 7. Given the mass of 1.500 Mg and a volume of 2.205 x 10^6 cc, what is the specific gravity? 0.685…

A:

Q: • Determine ly (from the centroidal Y-Y axis). Answer in in units.

A: moment of inertia :- moment of inertia of an area  about an axis is define as the second moment of…

Q: The top block weighs 50 lb while the bottom box weighs 25 lb. The coefficient of static friction for…

A:

Q: 4 A block of concrete weighs 550 N in air and weighs only 330 N when immersed in fresh water. What…

A:

Q: 2. An open U-tube having a diameter of 12mm contains mercury at a depth of 130mm. If 0.014 liters of…

A:

Q: SAMPLE PROBLEM Determine the horizontal and vertical components of the hinge force at B as it acts…

A:

Q: cube container is completely filled with water and weighed 245KN.

A:

Q: Discuss the relationship between bending moment, shear force and deflection, please provide all the…

A: The relationship between bending moment, shear force, and deflection is fundamental to the study of…

Q: A liter of water weighs about 97,500 dynes, what is the volume in cc.?.* 1500 cc 1000 cc 998 cc 994…

A:

Q: Make an introduction about Fluid Displacement Method for Measuring Volume Solids. Cite your…

A: To find the volume of an object or solid we can use the fluid displacement method.

Q: Fluid Mechanics / Static Fluid I have an exam please hurry up . choose the correct answer…

A: Weight per unit volume  is called specific weight.

Q: Write a short note about rigid body mechanics.

A: The analysis of bodies and structures in equilibrium is known as statics.

Q: An experiment on an ideal gas was conducted at a temperature of 170 degrees Fahrenheit [F] and a…

A:

Q: In a paragraph form, what are some things in everyday life that use hydrostatic pressure? List all…

A: (1) water tower water tower works under the hydrostatic conditions which is filled by pumps and…

Q: 8inch ↓ 12 inch ←

A:

Q: What is capillary in fluids? Explain capillary rise as well as capillary fall. Also provide the…

A: Capillary in fluids-It is the phenomenon of a liquid surface rising or falling in relation to the…

Q: Q3. A pump supplies water at a rate of 4 ft³/s and lifts water to a height of 15 ft. What is the…

A:

Q: Problem #2: Determine the resultant force magnitude and direction measured counterclockwise from the…

A:

Q: Find the kinematic viscosity of a liquid if you're given, Specific gravity = 1.4 Viscosity = 0.0040

A: Kinematic velocity is ratio of dynamic viscosity and density.

Q: In many applications, calibrated springs are commonly used to measure the magnitude of a force.…

A: Common force measuring tools The power produced by an engine, motor, or other rotating prime can be…

Q: 3. The temperature of an iron bar is 36°F. It is placed in an oven, after 1 and 2 minutes,…

A:

Q: 1. Consider a tanker truck as shown in the figure. The truck accelerates 4 m/s2. It is fully filled…

A: Solution: Given: a = 4 m/s2 ρ=726 kg/m3 Free body diagram: Assume the imaginary liquid surfaces of…

Hydrogen Energy

Energy is a quantity that cannot be defined, its existence can only be felt. In simple language, if a system possesses energy, it can do a specific kind of work. There are many forms of energy sources which people can use to obtain work. Solar energy, tidal energy, hydroelectric energy, geothermal energy, wind energy are some of the renewable energy sources which are primarily used for the production of electricity.