11. A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m, and then the hoop stress will be O(A) 30 MN/m² O(B) 50 MN/m² O(C) 100 MN/m² O(D) 200 MN/m²

11. A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of 1.5 MN/m, and then the hoop stress will be O(A) 30 MN/m² O(B) 50 MN/m² O(C) 100 MN/m² O(D) 200 MN/m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For a thin-walled cylindrical pressure vessel with hemispherical end caps, constructed of uniform thickness plate, the ratio of circumferential stress in the cylindrical shell to circumferential stress in the hemispherical shell is, TANK Оа. 1:0 O b.2:1 O. 1:2 O d. 1:1
The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of pressure of p. The state of stress at point "a" on the surface of the tank is represented by stress components with an unknown stress element rotation angle of 0. Note that, the two normal stress components for x'y' system (note: not xy system!) are known: ox, = 120 MPa and Oy = 180 MPa, but the shear stress component (T,) is unknown. Determine: (1) the principal stresses at point a ; (2) Tx'yı ; (3) rotation angle of 0 . y 180 MPa 120 MPа х 0 = ? a Tyy = ? tank cross section stress state at point a
The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. The thickness r,-r; is small compared to r; (a) Determine the axial force F in the ring in terms of p, w and r;. Hint: Consider a FBD by cutting the ring+membrane in two. (b) Determine the hoop stress in the ring. (c) Determine the hoop strain in the ring. The modulus of elasticity for the ring is E. (d) Relate the hoop strain to the change in the inner radius of the ring after this pressure is applied, and use this to get the change in the inner radius in terms of p, E, w, r, and ri- (PLEASE ANSWER ASAP AND CORRECTLY)!
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
A spherical pressure vessel 400 mm in diameter with a wall thickness of 15 mm. To what value may the internal pressure beincreased if the stress in steel is limited to 193 MPa?
6 üz Oy planmadı Ot üzerinden Txy tlenmiş oruyu tle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as Oy=67,9 MPa, oy=25,5 MPa and Ty=-24,3 as shown in figure (a). Determine the magnitude of the maximum in-plane shear stress (MPa). Yanıt:
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response: 8.16 m 3.68 m 07.36 m 4.08 m
A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure is 3 MN/?2 Determine The stress in the piston rod which has dimeter of 4 cm
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
I need complete solution without polagarise ASAP