100 mm 100 mm

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: 90mm 60mm 45mm R15mm

A: Let’s divide the given section into 3 sections. Section 1 is a rectangular OABC. Section 2 is the…

Q: 3

A: intro- defects on any material is cause of failure of material.

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: 2 m C 2.5 m 125 mm 1.5 m 25 kN/m 2 m 4 m

A: To determine the reaction at A and B, the beam can be dealt in two sections that are AD and DB. In…

Q: 300 mm 30º 300 mm 300 mm Can someone please label the projection of F and the rest of the…

A:

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: determine and plot the moment M rotate arm 0A over the range 0 < Find the maximum value of M and

A:

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: Determine the following based on the given illustration: a) Area of the Composite figure

A: To determine the area of the composite figure.

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: 10 mm Y 15 mm 30 mm 40 mm 10 mm 15 mm X

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: The motor produces 30kW to the A-36 steel solid shaft at a frequency of 20HZ. The shaft is 70mm in…

A: Given data as per question diameter of shaft (d)=70 mmω=20 Hz=20×6.28=125.6 radsPower developed by…

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

A:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: A 15-meter long beam-tank assembly supports the loading shown in addition to its weight, which is a…

A: To Find:the moment of inertia.Given:The outer diameter of cylinder is .The inner diameter of…

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: Perform unit conversion. 28.9 nm to μm

A: Given 28.9 nm To be find Convert to μm

Q: A cylindrical tapered section of diameters 25 mm and 50 mm with a length of 200 mm is pulled along…

A: The Total elongation of the rod cylindrical tapered section. As from the figure i had taken small…

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: What is the aerodynamic (equivalent) diameter of an airborne spherical aluminium particle with the…

A: From the given data,material of particle is aluminum so, ρal. = 2.7 g/cm3da = here ds = 3 micro…

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: 4 ft A 2 ft 4 ft 2 ft The engine hoist shown above support a 1.2 kip engine, with a center of…

A: Given: The engine load, W = 1.2 kip

Q: 300 N 36 mm

A: We need to apply force equlibirium equation along the horizontal direction∑Fx=0Ax-C=0......consider…

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.