1. PRELIMINARY WORK: 1.1 Explain how to test a BJT to determine whether it is defected or not, by means of an ohmmeter? 1.2 For the circuit given in Fig. 2, Q1 is an npn-BJT where VBE,ON=0.7V, VBc,ON=0.7V, and B=100. What should be the minimum value of RB for the BJT to function in active mode if VBB=5V, Vcc=10V, and Rc=1k2, Re=4702. (Hint: Write two KVL equations for B-E and B-C terminals). Vcc Rc Ic RB V BB Q1

1. PRELIMINARY WORK: 1.1 Explain how to test a BJT to determine whether it is defected or not, by means of an ohmmeter? 1.2 For the circuit given in Fig. 2, Q1 is an npn-BJT where VBE,ON=0.7V, VBc,ON=0.7V, and B=100. What should be the minimum value of RB for the BJT to function in active mode if VBB=5V, Vcc=10V, and Rc=1k2, Re=4702. (Hint: Write two KVL equations for B-E and B-C terminals). Vcc Rc Ic RB V BB Q1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the BJT, we can account for IB physically by the following mechanisms: A. some carriers will be injected from the base to the emitter, B. there must be some recombination in the base, C. A and B above. O If the base-emitter junction is reversed biased and the base-collector junction is forward biase the transistor will be at what region of operation? A. active region, B. cutoff region, C. saturation region, D. breakdown region. • What region the transistor should be operating to have minimum distortion at the output sign: A. active region, B. cutoff region, C. saturation region, D. None of the above. • For an "on" silicone transistor, the voltage VBE should be in the neighborhood of A. 0.3 V, B. 0.55 V, C. 0.7 V, D. 1.7 V.
stap-by-step with explanation. Consider a single-electron transistor, where the two tunnel barriers (between island and source, and island and drain) each have a tunneling resistance R = 100 kOhm.Calculate the value of source-drain bias voltage V_SD such that every electron that traverses the SET island spends, on average, 1 nanosecond on it. Express the value in microvolts.
An npn transistor has a CBJ with an area 120 times that of the EBJ. Find the voltage drop across EBJ and across CBJ when each is forward biased and conducting a current of 2 mA. Also find the forward current each junction when forward biased with 0.6 V
Discussion:- 1. When are the p-n junctions of the n-channel FET blocked? 2. When cre the p-n junctions of the p-channel FET blocked? 3. What is the significance of the deviations between the two on-state characteristics? 4. BJT is considered as a device controlled by current while FET is a device controlied by. . 5. Explain how the channel n or p is punch off when vas increased.. 6. BJT is more linear than FET. Why? Explain 7. what is vas (off)? How could it effects the operation of the FET? 8. What is IDS ?
Pls i need answer to this question
A given BJT has an alpha of 0.9985 and a collector current of 15 mA. What is the value of base current? a. 0.0225 mA b.15.15 mA c. 14.85 mA d. 15 mA
For the circuit given below, suppose that RB = 230k2, RE1 = 4002, RE2 = 02, Rc = 1002 and Vcc = +6V. Given that the BJT's have B=100, verify that the transistors are in active region by finding icı, VCE1, İc2 and VCE2. Active region: VBe = 0.7V Q+Vc RB Rc Q1 Q2 Re1 RE2
For a particular n-channel MOS technology, in which the minimum channel length is 0.2 μm, the associated value of λ is 0.5 V-1. If a particular device for which L is 1.0 μm operates in saturation at vDS = 1 V with a drain current of 100 μA, what does the drain current become if vDS is raised to 2 V? What percentage change does this represent? What can be done to reduce the percentage by a factor of 2?
In common base configuration of BJT, if it is working in the active region then the collector current will be approximately equal to the emitter current. True False A Moving to another question will save this response. Activa Go to Se
An npn transistor operates in the active mode when both of of its 2 pn junctions are forward biased. Select one: 1.True 2. False
29 - Which of the following is true?A) In order for the BJT transistor to operate in the active region, the correct polarization must be between the Beyz-Collector.B) BJT transistors are 2 types of N-channel and P-channel.C) For the BJT transistor to operate in the active region, the reverse polarity between the Beyz-Emitter must be.D) For the BJT transistor to work in the cut-off area, the correct polarization between the Beyz-Emitter must be.E) For the BJT transistor to operate in the saturation region, the correct polarization must be between the Beyz-Collector.
|vp| 1V. For For the PMOS transistor in the circuit shown in Figure, K, = 8μA/V², W/L = 25, and = 100μA, find the voltages VSD and VSG for R = 10k. For what = VSG? = value of R is VSD +10 V VSG VSD