1. At the proportional limit, a certain material has a stress of 78 MPa as the strain is 0.0004. What is the modulus of elasticity of the material in GPa?

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A:

Q: The tank shown in the figure is fabricated from a 10 mm steel plate. Determine the longitudinal and…

A:

Q: Question 11 of 12 - / 1 Current Attempt in Progress A 33 mm by 33 mm square ABCD (i.e., a = 33 mm)…

A: In this problem, we are given a square that is deformed into a rhombus due to the application of a…

Q: mine the normal stress in a ball, which has an outside diamete d to a gage pressure of 66 kPa. er:0,…

A:

Q: Example 2.36. A railway is laid so that there is no stress in the rails at 8°C. Calculate (a) the…

A: Given :

Q: Problem 2: Determine Maximum Normal stress. Golb 90b 20lb

A:

Q: If the hoop stress on a cylindrical pressure vessel with diameter d, thickness t and gauge pressure…

A: Solution:-

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50kN.…

A:

Q: A solid shaft has to transmit 50 kW of power at a speed of 1910 RPM, Ignore any possible bending of…

A:

Q: J.20 (C). A thick cylinder of 100 mm internal diameter and 125 mm external diameter is wound with…

A: step 1-

Q: A cylindrical tank holding oxygen at 1,146 kPa pressure has an outside diameter of 430 mm and a wall…

A:

Q: A hollow steel tube with inside diameter of 100mm is carrying a tensile load of 400kN. Determine the…

A: Steel tube is given with, External Diameter of 115mm Internal Diameter of 100mm  Carrying a tensile…

Q: Answer

A:

Q: Q.6 A solid shaft is subjected to a bending moment of 500 Nm and a torque of 700 Nm. Calculate the…

A: given Bending moment M=500 NmTorque T=700 Nmpermissible normal stressσb=100 MPa

Q: Determine the normal stress in a ball, which has an outside diameter of 195 mm and a wall thickness…

A:

Q: EXAMPLE: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN.…

A: in given question, hollow steel inside diameter=100mm, has tensile load of 400KN given stress=…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A:

Q: 15 N-m 25 N-m 30 N-m B 60 N-m 70 N-m

A: Let us analyse the question in step 2.

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.? is stretched between two fixed…

A:

Q: : Calculate and sketch the normal stress distribution acting over the cross section at section a-a.…

A:

Q: A strain gage is mounted at an angle of 30° with respect to the longitudinal axis of the cylindrical…

A: Diameter of cylinder = 54 inch  Internal pressure = 0.702 ksi  E= 10000 ksi  v= 0.33

Q: Theory of Failure Question 1: The uniaxial yield stress of a material is 866 MPa. According to von…

A: Yield stress- σy=866  MPa, It is needed to find the shear yield stress as per the Von-mises…

Q: A cube of material (E 15,000 psi, v 0.25) of side length 2" is shown in the x, y plane. Take x…

A: Change in length of the cube depends on the length of the sides of the cube and the normal stress…

Q: MPa IR E mm/mm 0=S0,00E + 165 J-160000E 0=J0,0012 (E-0.00 +265

A:

Q: QUESTION 1 a) A bar 30 mm in diameter and 80 mm in length is subjected to a tensile load 100KN. The…

A:

Q: A cylindrical tank holding oxygen at 2.091 kPa pressure has an outside diameter of 409 mm and a wall…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.