(i) Total head at A and B(ii) Hydraulic gradient.(iii) Flow rate. 1 m-1m.SoilB1 m0.8 mDatumTableFigure Q2 (b)(i) Total head at A and B(ii) Hydraulic gradient.(iii) Flow rate. A soil sample 12 cm in diameter is placed in a tube 1 m long. A constant supply of water isallowed to flow into one end of the soil at A, and the outflow at B is collected by a beaker. The(b)average amount of water collected is 2.5 cm3 for every 5 seconds. The tube is inclined as shownin the Figure QI. Determine the :

Answered: 1 m A Soil B 1 m 0.8 m Datum Table…

Engineering

Civil Engineering

1 m A Soil B 1 m 0.8 m Datum Table Figure Q2 (b) (i) Total head at A and B (ii) Hydraulic gradient. (iii) Flow rate.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: At a wastewaterdischarge point, 2500 L/s of effluent must be conveyedin a straight…

A: Q = Discharge = 2500 L/s = 2.5 m3/sy = Depth of flow = 0.55 m.b = Width of base = 1.8 mThe channel…

Q: Example. The water depth upstream of a sluice gate is 0.8 m and the depth just downstream (at the…

A: Given data- Water depth upstream of the sluice gate h1=0.8 m, Depth just downstream h2=0.2 m, To…

Q: A municipal WWTP receives 20,000m3/d of flow. They use two circular primary clarifiers operate in…

Q: 4 For a rectangular channel, if the Froude number = 1.5 and the initial depth=0.8 m, the depth after…

Q: A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and…

Q: View Policies Current Attempt in Progress Water flows in a 0.15-m-diameter vertical pipe at a rate…

Q: A right-angled triangular channel carries a flow of 16,000 l/s. The Manning's n = 0.020 and the…

Q: Show all the necessary figures (if applicable) 1.5) Points A and B are separated by 915 m of new…

Q: Compute the velocity of the flow for a very smooth pipe if the hydraulic radius is 10ft, and slope…

A: we have hazen williams equation:V=1.318CR0.63S0.54so,C=coefficient ; for smooth pipe…

Q: The water depth upstream of a sluice gate is 0.8 m and the depth just downstream (at the vena…

Q: A rectangular channel discharges 0.5m/s per metre width. Determine the critical depth and the step…

A: Given data: q=0.5 m3/s/m E1=1 m

Q: u = Ug · e where free flow speed density optimum density k ke

Q: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the…

A: Discharge Bed level of the canal The crest level of the regulator = Upstream water level = 54.2…

Q: A drainage canal having a trapezoidal shape has a base equal to 2 m laid to a slope of 0.0015. The…

A: given data b=2m slope=0.0015 q=7.05m3/sec side slope=1:1 N=0.012 1.determine depth of flow d*(n2+1…

Q: give the right answer please

A: The water will flow upward.Explanation:Step 1: As we know that water flows from the high pressure…

Q: E √d=31 _-_|d=31m b=2.3m V=3m/s Find discharge.

A: Given that b = 2.3 m d = 3.1 m Velocity v = 3 m/s Area of cross section A = b × d A = 2.3 × 3.1 =…

Q: 10. For isothermal flow and non-flow steady processes, prove that S₁ pdv v.dp 1 Also state the…

Q: 5(c) Water flows at a rate of 100 m³/s in a rectangular channel whose width is 3 m. Find the…

A: Given- Discharge Q=100 m3/s Width b=3 m It is needed to find the critical depth of the flow.

Q: 5) Water flows in a rectangular open channel having a width of 2 m with a flow rate of 10 m³/s as…

Q: Determine the Headloss at Pipe 1 in METERS b.) Determine the Headloss at Pipe 3 in METERS c.)…

A: Solution: Given : Length of pipes=500m Friction factor (f)=0.02 The flow rate in Pipe 1…

Q: 1) Which location has positive, negative, zero pressure? a) 3, 1, 2 b) 2, 1, 3 c) 2, 1, 3 d) 2,…

Q: A flow of water of 0.1 m³/sec flowing through rectangular tube of width 550 mm and having adjustable…

A: Given: Discharge, Q = 0.1 m3/s Width, W = 550 mm Depth, H = 250 mm C = 55

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water: Pv=2.25kPaAtmospheric Pressure, Patm = 100 kPaγwater =9810…

Q: Part 1: Determine the Froude number and the type of flow. Water flows at a rate of 8.5 m3/s in a…

A: Water flow rate = 8.5m3/sec Width of channel = 2.25m Depth of channel = 0..32m It has been asked in…

Q: In gradually varied flow, the channel bottom, water surface, and EGL are parallel. Select one: O…

A: Given Channel bottomWater surfaceEGLTo find out TRue or false

Q: Open channel flow

A: Given data : Depth of flow (d)=2.5 mwide (B)=5 m

Q: Find the maximum step height for a flow with a constant discharge, q = 12 m2 /s, and at 1 a water…

Q: 2. Designing an open channel to convey the water to the two downstream communities where, the |…

Q: Water flows through a large size pipe with total and static pressure head of 0.5m and 0.3m of fluid.…

Q: Q) Water is flowing in three side-by-side pipes of diameter (1.8m) each. The Manning's (n) and the…

Q: (c) A sewage treatment plant is designed for an a circular primary clarifiers are arranged in…

A: cWe know weir length = πD for one clarifierso2πD=70mD=11.1408m

Q: Q3/ Determine the state of flow in a rectangular channel of (3m) width and depth of flow is (1m) and…

Q: Water is flowing in trapezoidal channel at a depth of 1.20 m with a bottom width of 7.00 m and has a…

A: Froude number: Froude number is defined as the ratio of inertia force to the gravitational force.…

Q: Pb # 2: Water at 60 °C flows in a straight 24-mm-diameter pipe (e = 0.060 mm) between points A and B…

A: Given data Registration number = 5350 Temperature of water= 60° C Dia of pipe= 24 mm Length of…

Q: The concrete pipes culvert (n = 0.012) must carry the flow from open channel half square section 4m…

Q: A water treatment plant has an average influent flow rate of 15 MGD and peak flow rate of 25 MGD…

Q: (e) The flow Q = 300 cfs goes under the sluice gate that extends across the width of the channel.…

A: Data given n =0.015 B = 60 ft S = 3 per 1000 Q = 300 cfs Find: (e) GVF curve after sluice gate (f)…

Q: Water flows uniformly in a finished concrete rectangular channel (n = 0.02) with a bottom width of…

A: 1. bottom width of the channel = 0.85 m2. Flow depth in the channel = 0.4 m3. bottom slope of the…

Q: A straight pipe has a diameter of 25 mm, a roughness height of 0.1 mm, and is inclined upward at an…

A: The given data is shown below: Diameter=25mmRoughness height=0.1mmInclination=10°Temperature=20°C

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

(i) Total head at A and B
(ii) Hydraulic gradient.
(iii) Flow rate.

A soil sample 12 cm in diameter is placed in a tube 1 m long. A constant supply of water is
allowed to flow into one end of the soil at A, and the outflow at B is collected by a beaker. The
(b)
average amount of water collected is 2.5 cm3 for every 5 seconds. The tube is inclined as shown
in the Figure QI. Determine the :

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

design a river intake given the winter flow is 30 mgd and the summer flow is 55 mgd and the depth durring summer is 8ft and the depth for winter is 15ft.
the flow rate is 1.2 m3/s per meter of channel width. (a) Compute the velocity and water depth at the top of the budge (hmax= 0.1 m). Characterize the flow there. (b) Rework the problem for a flow rate three times as large.
Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A lined rectangular channel (n = 0.015) has a flow depth of 2m and a bed slope of 1 in 1600. Width of a channel is equal to the last digit of your registration number in meters. Retaining the rectangular shape and same total perimeter of a lining, DISCOVER the change in discharge for a most efficient x-section of a channel, if the bed slope, channel width and manning’s n remain same. b).DISCUSS the critical depth, normal depth and hydraulic depth of flow for subcritical and supercritical flow in open channel.
Subject : Fluid mechanics Please read the question carefully and give me right solution according to the question. Thank you
Please show all steps and carry the units. Thank you
Solve 6.3 only
Water is flowing in three side-by-side pipes of diameter (1.8m) each. The Manning's n and the bed slope of each pipe are (0.017) and (1:1000) respectively. The water depth in each pipe is (1.3 m). After the development, the discharge above is expected to increase by (32%), and the engineers have decided to replace the three pipes by a trapezoidal channel. The new channel should have (n= 0.02) with the same bed slope, B = 1.45 y, and z=1.5. Design the cross section of the new channel and state the type of .flow (subcritical or supercritical)
5.) A horizontal pipe gradually reduces from 250 mm to 150 mm diameter section, the pressures are 90 kPa and 70 kPa, respectively. If the flow rate is 15 L/s of water, compute the head lost (m) between the two sections.
Specialization: Civil Engineering Module Name: Hydraulics
Complete answer
Determine the phase of water at T = 260 C, P = 5MPa T = -2 C, P = 100kPa
A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and 3.8 cm deep. The minimum allowable spacing for the bars is 2.4cm. The appoach channel carries the water at velocity of 0.381 m/s and is 1.07 m wide and 1.37 m deep. 1- detrmine the number of bar and spacing that should be used. 2- calculate the head loss through screen when it is clean (m). 3- it's estimated that the screen will remove 227 kg (wet basis) of screenings ber milion gallons of water treated. What will be the daily accumulation (kg and m^3) of the screening if the density of screening 100 kg/m^3.