1- Calculate the steady discharge (Q) and the power consumption (P) for a pipe connected between two water tanks. Pipe diameter 300 mm (Ds = Da); Length = 3500 m; Pipe roughness e = 0.1 mm; Water viscosity = 1.3 x 106 m²/s; Minor losses coefficient k = 8.0, Static Lift = 12 m. Pump Characteristics discharge (1/s) Total head (m) Overall efficiency (per cent) 0 30 10 28 44 20 23 58 30 17 50 40 8 18

1- Calculate the steady discharge (Q) and the power consumption (P) for a pipe connected between two water tanks. Pipe diameter 300 mm (Ds = Da); Length = 3500 m; Pipe roughness e = 0.1 mm; Water viscosity = 1.3 x 106 m²/s; Minor losses coefficient k = 8.0, Static Lift = 12 m. Pump Characteristics discharge (1/s) Total head (m) Overall efficiency (per cent) 0 30 10 28 44 20 23 58 30 17 50 40 8 18

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5): For the system shown below: 1-Find the water power of the turbine (PT) if the required power output is PE (take PE between 5-25 kN) and the turbine efficiency is n (take n between 75 to 98%) 2- Find the flow rate in the pipe AB. 3-Find the value of Z1 for operating this system (take Z2 between O to 20 m). * Pitot tube Piezometer. 0.3m 1.0m z1 22 T. Id= 200mm d= 100mm
Complete solution pls
The allowable Net Positive Sustion Head (NPSH) for a pump provided by the manufacturer for a flow of 0.05 m³/s is 3.3 m. The temperature of water is 30° C (vapour pressure head absolute = 0.44 m), atmosphere pressure is 100 kPa absolute and the head loss from the reservoir to pump is 0.3 N-m/N. Find the maximum height of the pump above the sustion reservoir.
simple solution is needed
• Calculate the Hydraulic rate Vo, and BOD load of a single -stage trickling filter with the following data: Q= 30000m3/d, t=3hrs, H=2m and BOD effluent 30mg/l, Recirculation around filter is =25%Q. Assume efficiency of filter 80%.
solve
Problem1: A new coagulation water treatment plant is proposed to treat 0.1145 m³/s at an average temperature of 19 °C. The tank is circular, and the required water depth is twice the diameter. Using the following design assumptions: detention time=10s; velocity gradient = 800 s¹; impeller type: radial flow turbine with 6 flat blades and assume B-H/3. Determine a) The tank dimensions b) The impeller diameter knowing that the available diameters are 0.45 and 0.6 m c) The required input power
Q-5
2.Water (ρ = 1000kg / m3, μ = 10-3Pa.s) flows at a speed of 1.6m / s (Reynolds number Re = 0.8 105) in a pipe whose diameter is to be determined.
(a) Water at temperature of 20 °C is pumped from a reservoir to a large open surface storage tank through a piping system with diameter of 10 cm as shown in Figure Q1. A pump with pump head rise ha = 32 – 1 × 10°Q²,Q = is m? installed in this system. Besides, the pipe's fitting components installed in this piping system such as tee and long radius 90° elbows are flanged type. The total pipe length for the entire piping system from reservoir to storage tank is 48 m while the pipe length from reservoir to pump suction side is 8 m. The friction factor of the pipe in this system is estimated to be 0.02. The elevation difference between the reservoir and storage tank are estimated to be 18 m. Water at 20°C D= 10 cm 18 m pump Reservoir Figure Q1
The commercial steel tube is then 100 m long and0.4 m in diameter. Calculate the height of the tower h, if the flow speed for7.95 m / s. Consider that losses are negligible and that losseswater temperature is 4 ° C
Be fast and quick and correct.