1: AW 5 x 16 wide flange is subjected to a suspended tensile load at one end. There are 6 sets of 25 mm diameter fasteners holes at the web center along the direction of loading. The distance between center of the holes is 80 mm along the direction of force. Using Fy = 248 MPa and Fu = 440 MPa find the tensile capacity (LRFD & ASD). Use U = 0.70 (see table 504.3.1 of NSCP 2015 Given: diameter of hole = 25 mm bf=127 mm tf=9.14 mm Ag = 3,019 sq mm d=127.25mm tw = 6.1mm U = 0.70

1: AW 5 x 16 wide flange is subjected to a suspended tensile load at one end. There are 6 sets of 25 mm diameter fasteners holes at the web center along the direction of loading. The distance between center of the holes is 80 mm along the direction of force. Using Fy = 248 MPa and Fu = 440 MPa find the tensile capacity (LRFD & ASD). Use U = 0.70 (see table 504.3.1 of NSCP 2015 Given: diameter of hole = 25 mm bf=127 mm tf=9.14 mm Ag = 3,019 sq mm d=127.25mm tw = 6.1mm U = 0.70

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

solve the given and show your complete solution.
A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All structural steel is A992. Check this connection for compliance with the AISC Specification. Assume that the bearing strength is controlled by the bearing deformation strength of 2.4dtFu. a. Use LRFD. b. Use ASD.
please help my homework.thank you very much. my questions subject is fundamentals of steel design
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 4 inch boltas shown below. Use A36 steel with Fy=36 ksi and Fu=58 ksi Properties and Dimension Ag=35.30 in^2 ... rX = 6.24 in ry = 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in Y k1=1.5 k=1.54 I tf=0.94 d=14.5 Etw=0.59 bf=14.7 A. Determine the Yielding Capacity of the section based on LRFD (kips) Round your answer to 2 decimal places.
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area?
4. Design the reinforced lap joint as shown in Figure 6.2. The plates are 7 in wide of A36 steel and the SMAW process is used. The given load is 25% dead load and 75% live load. 45° 100k VT VT 100k
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by ¾ inch boltas shown below. Use A36 steel with Fy=36 ksi and Fu=58 ksi
Q2: aluminum rod AB (G 27GPA) brass rod BD (G = 39GPA). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram
A column is formed by welding two A36 MC sections back-to- back. The column is 32 feet long. With respect to x-axis buckling, supports are hinged at the top, and fixed at the bottom. With respect to y-axis buckling, supports are pinned at both ends. Additionally, hinge supports are provided at the mid-height perpendicular to both axes. Use the recommended k-values. Below are the properties of a single MC section: A=6.45 in2, d=10 in, bf-3.32 in, x=0.990 in, Ix=102 in¹, ly=6.40 in, rx-3.99 in, ry=0.997 in
Calculate the maximum shear stress in the cross section shown if the total shear load applied is 5000 lbf. The properties for the upper and lower spar caps are given below and assume the web to be effective in resisting bending stress. 0.6" 1 = 0.2 in 4 A = 0.95 in ² 5.4" web Spar cap 0.056" ΝΑ 12" (SEE HAND ANALAYSIS) Hand written asap
Please help me. I'll give a thumbs up
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2