.(c) A brick masonry wall of size 450mm is carrying a load 120 kN/m. Find the depth of a RCC strip footing (i) (ii) (iii) (iv) (v) (vi) (vii) Depth of foundation: 1.20m Unit Weight of backfill: 16 kN/cum Net Allowable Bearing Pressure: 80 kN/m2 Unit Weight of R.C.C. : 24 kN/m2 Unit Weight of Brick Masonry: 19.8 kN/cum Grade of Concrete: M25 Grade of Steel : Fe-415

.(c) A brick masonry wall of size 450mm is carrying a load 120 kN/m. Find the depth of a RCC strip footing (i) (ii) (iii) (iv) (v) (vi) (vii) Depth of foundation: 1.20m Unit Weight of backfill: 16 kN/cum Net Allowable Bearing Pressure: 80 kN/m2 Unit Weight of R.C.C. : 24 kN/m2 Unit Weight of Brick Masonry: 19.8 kN/cum Grade of Concrete: M25 Grade of Steel : Fe-415

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Along footing, 3 ft wide, is located in the slope of a hill whose inclination is 30°. The soil of the hill is sand that has an angle of internal friction of 35° and a unit weight of 115 pcf. If a D/B ratio of 1 is assumed, what wall loading can the footing carry? Use a factor of safety of 3.
2. A masonry terrace of 85mm thick concrete surface with 35mm thick cement tiles rest on 200mm x 250mm timber spaced at 350mm on centers acting as simple beam with effective span of 3.8 meters. Weight of wood is 9.5Kn/M^3 and masonry to be 20KN/m^3. Ew = 13.8GPA. %3D CEMENT TILES Given: 65 %3D Allowable stresses for bending = 14 MPa Seil 250 For shear parallel to the grain = 0.9 MPa FLOOR 200 01ST Deflection = 1/360 of span %3D 250 350 200 a. Determine the uniform load it could support with respect to bending. b. Determine the uniform load it could support with respect to shear. c. Determine the uniform load it could support with respect to deflection.
A square spread footing supports a square tied column as shown. Assume that the reinforced concrete is normal weight (24 kN/m3) and = 1.00 (NSCP C101-15 Table 419.2.4.2). The column has a height of 3.5 meters. 1. Check NSCP code requirements for the reinforcement: (a) longitudinal bar clear spacing, (b) steel ratio, (c) minimum number of bars, (d) minimum lateral tie size, (e) spacing of ties, and (f) arrangement of ties. 2. Calculate the plan dimensions (L m x L m)of the spread footing. Assume a trial thickness of the footing H = 750 mm. 3. Calculate the effective depth d (mm) considering punching shear (two-way shear).
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
2. Design a one-way slab to carry a service live load of 4000 Pa. The slab has a length of 4m with both ends continuous. Assume f'c = 21MPa and fy = 415 MPa for main bars and fy=276 MPa for temperature bars. Unit weight of concrete is 23.5 kN/m³.
Problem # 3 A combined footing supports an exterior column 16 in x 16 in carrying a service dead load of 155 kips and a service live load of 165 kips, plus a 22-in.-square interior column carrying service loads of 205 kips dead load and 230 kips live load. The distance between the columns is 18 ft, center to center. For shallow foundations, the allowable soil bearing pressure is 4 ksf and the bottom of the footing is 4 ft below final grade. Design the steel in long direction using fc' 3 ksi, fy 60 ksi.
A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
C PLEASE SHOW THE SOLUTION. THANK YOU
Foundation and Retaining Wall Design 3 Decimal Places
A 12 in wide concrete block wall carries an unfactored vertical design load of 25.1 k/ft. The sustained vertical load for serviceability analysis is 18.4 k/ft. It is to be supported on a continu-ous footing made of 2,500 lb/in2 concrete and 40 k/in2 steel. The soil has an allowable bearing pressure for bearing capacity of 6,700 lb/ft2 (using ASD methods) and an allowable bearing pressure for settlement of 4,000 lb/ft2 . The groundwater table is at a great depth. The localbuilding code requires that the bottom of this footing be at least 24 in below the ground surface.Determine the required footing, width, thickness, and design the lateral and longitudinal steel.Show your design in a sketch.
Geotechnical engineering -2 (foundation engineering) Solve the following problem with complete solution thank you so much here is 5:09pm i need it by 5:50pm thanks! :)
Design a simply supported one- way slab with ln=4m. Let fy=276MPa, f’c=21MPa, db=10mm and Cc=20mma. Determine the thickness of the slabb. Determine the required reinforcement spacing and check the for minimum and maximum values set by NSCP.