Asm CSINewsletter-08

Each of the following statements describes a way of coping with temperature variation. Which scenario most likely includes positive heat transfer through convection? That is, in which scenario does Hconvection most likely have a positive (+) sign? Hanimal = +SR + IRin – IRout +/- Hconvection +/- Hconduction - Hevaporation + Hmetabolic Select one: a. A rabbit basking in the sun early in the morning. b. A lizard resting in the shade in a hot desert in the middle of the day. c. A bumblebee vibrating its flight muscles before flight. d. A ground squirrel hibernating in the winter. e. A bird fluffing its feathers on a cold day.

https://us.humankinetics.com/blogs/excerpt/managing-air-pollution-for-athletes What is talking about this report and What did you reach at the end of this article?

APPLICATIONS OF FIRST ORDER DIFFERENTIAL EQUATIONS Newton’s Law of Cooling and Joint Proportions   At 4:00pm, a thermometer reading of 28 deg C is taken outside where the ambient temperature is –11 deg C. At 4:05 pm, the thermometer reads 8 deg above zero. After a while, the thermometer is returned to the room maintained at 28 deg C. At 4:12pm, the thermometer reads 15 deg C. When was the thermometer returned to the room?

Which of the following formulas describe the thermal efficiency of a cycle? Select all that applies.     1 - qin/qout     worknet/qout     worknet/qin     1 - qout/qin

Subject: Air Pollution Formation and Control Do not just copy and paster other online answers Estimate the total volumetric flow rate gas and the total mass emission rate of the particles in Fig 4.3. Ans : (a) volumetric flowrate = 1.9E3 ft3/s or 1.1E5 acfm  ;  (b) mass flowrate = 58 lbm/hr

perform a 5 whys with the following topic: *  air temperature in a paratrooper

Q.1 a. Repeatability and reproducibility are ways of measuring precision, particularly in the field of engineering. i. What is an engineer's expectation when performing repeatability or reproducibility? ii. State a difference between repeatability and reproducibility in an experiment? b. Figure Q.1 shows the measurement data of two types of thermal transducers namely thermocouple. Турe E Туре К 6.8 4.2 20 40 60 80 100 Temperature Difference (°C) Voltage Output (mV)

The activities, duration and cost under normal and crashed conditions for a network diagram are shown in the accompanying table.    1. Determine the normal duration of the project 2. Determine the normal cost of the project 3. Determine the critical path under normal conditions.

Which of these statements are correct?

View Policies Current Attempt in Progress A High-Performance Engine. You and your team are tasked with evaluating the parameters of a high-performance engine. The engine compresses the fuel-air mixture in the cylinder to make it ignite rather than igniting it with a spark plug (this is how diesel engines operate). You are given the compression ratio for the cylinders in the engine, which is the ratio of the initial volume of the cylinder (before the piston compresses the gas) to the final volume of the cylinder (after the gas is compressed): VV, Assume that the fuel-gas mixture enters the cylinder at a temperature of 26.0 °C, and that the gas behaves like an ideal gas with y-7/5. (a) If the compression ratio is 14.9:1, what is the final temperature of the gas if the compression is adiabatic? (b) With everything else the same as in (a). what is the final temperature of the gas if the compression ratio is increased to 16.117 (c) Everything else being the same, for which compression ratio…

Submit correct and complete solutions. give propriate Explanation. Provide step-by-step detailed explanations.

thermodynamics   Ten kilogram of water us mixed with 12 kilogram of alcohol (SG=0.9).What is the specific gravity of the mixture, assuming that two fluidsmix completely.

Please solve and answer the question correctly please. Thank you!!

##What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing Adsorption Oxygen Generator (PSA) COMPs = Compressors POMPs = Pumps HEAT = Heat Exchanger PV = Flow Valves ST TANK = Storage Tank VENT = Vent DR = Drains PSV = Pressure Relief Valve In addition, what would be the possible problems that would require flexibility correction by adding expansion joints, spring supports, anchors and brackets?

I need a rules used in the ventilation system for the report "air quality and safe entertainment in sports halls" like this photo below but for ventilation system formulas

(b) A special sprinkler system is comprised of three identical humidity sensors, a digital controller, and a pump, of which the reliability is 0.916, 0.965, and 0.983 respectively. The system configuration is shown in the figure below. Sensor Controller Pump Reliability block diagram of a sprinkler system. (b) Calculate the reliability of the sprinkler system. (c) Discuss the importance of safety in an engineering maintenance.