Jackson Weber VSIM Reflection

Hartley Electronics, Inc., in Nashville, producesshort runs of custom airwave scanners for the defense industry.The owner, Janet Hartley, has asked you to reduce inventory byintroducing a kanban system. After several hours of analysis, youdevelop the following data for scanner connectors used in onework cell. How many kanbans do you need for this connector?Daily demand 1,000 connectorsLead time 2 daysSafety stock 12 dayKanban size 500 connectors

You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…

Analysis and Interpretation of vertical Ground Reaction Forces. In this study, a volunteer was asked to walk on two force platforms under two different conditions. Condition 1- Normal Walk (NW), condition 2 - walking over an obstacle (ObsW). The right limb was the one to step on platform 1 in both conditions. The force platforms were used to measure the vertical ground reaction forces on the right limb. Data was collected on Vicon (Nexus) software and the attached graphs ( mean NW/ObsW, Mean (+-)1SD NW/ObsW) were created. Analyse ,Interpret the graphs and make a conclusion of the result attached.

I want to briefly summarize what he is talking about and what you conclude. pls very urgent

Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question is Attached in image. Thank you.

Analysis and Interpretation of vertical Ground Reaction Forces. In this study, a volunteer was asked to walk on two force platforms under two different conditions. Condition 1- Normal Walk (NW), condition 2 - walking over an obstacle (OW). The right limb was the one to step on platform 1 in both conditions. The force platforms were used to measure the vertical ground reaction forces on the right limb. Data was collected on Vicon (Nexus) software and the attached graphs ( mean NW/OW, Mean (+-)1SD NW/OW) were created. Analyse and Interpret the graphs attached.

A nearsighted eye is corrected by placing a diverging lens in front of the eye. The lens will create a virtual image of a distant object at the far point (the farthest an object can be from the eye and still be in focus) of the myopic viewer where it will be clearly seen. In the traditional treatment of myopia, an object at infinity is focused to the far point of the eye. If an individual has a far point of 39.5 cm, prescribe the correct power of the lens that is needed. Assume that the distance from the eye to the lens is negligible.

Hello tutors, help me. Just answer "Let Us Try"

please show work answer is D

University of Babylon Collage of Engineering\Al-Musayab Department of Automobile Engineering Under Grad/Third stage Notes: 1-Attempt Four Questions. 2- Q4 Must be Answered 3-Assume any missing data. 4 تسلم الأسئلة بعد الامتحان مع الدفتر Subject: Mechanical Element Design I Date: 2022\01\25 2022-2023 Time: Three Hours Course 1 Attempt 1 Q1/ Design a thin cylindrical pressure tank (pressure vessel) with hemispherical ends to the automotive industry, shown in figure I below. Design for an infinite life by finding the appropriate thickness of the vessel to carry a sinusoidal pressure varied from {(-0.1) to (6) Mpa}. The vessel is made from Stainless Steel Alloy-Type 316 sheet annealed. The operating temperature is 80 C° and the dimeter of the cylinder is 36 cm. use a safety factor of 1.8. Fig. 1 (15 Marks) Q2/ Answer the following: 1- Derive the design equation for the direct evaluation of the diameter of a shaft to a desired fatigue safety factor, if the shaft subjected to both fluctuated…

Newton's Law of cooling states that the rate at which heat is lost by a heated body is proportional to the difference in temperature between the body and the surrounding medium. Match the following statements/phrases with the corresponding item in the drop down box. Choices in the box 1. In accordance with the stated law obove, we have the equation? 2. If a thermometer is taken outdoors where the temperoture is 5 deg C, from a room in which the temperature is 20 deg C and the reading drops 10 deg C in one minute, the working equation is? 3. In the obove problem, separoting the variables and integrating will result to? 4. In the obove problem, how long, in minutes, after its removal from the room will the reading be 6 deg C? 5. In the obove problem, ofter 30 seconds, whot will be the thermometer reading? 5.2 dT(body temp)/dt = k(Temp of medium - 5) dr(body temp)/dt = k(Temp of body - Temp of medium) Temp of body = Cenkt +5 2.5 13.7 dr(body temp)/dt = k(Temp of medium - Temp of body)…

Thermodynamics Please READ THE PROBLEM! I’m tired of posting the same problem over and over. please Read. This is what the asking for please: -1. sketch and label all your answers on the nozzle -2. Sketch and label all your answers on the process on a P-V diagram.... Thank you

You have been asked by your supervisors at A&L Engineering to design a roller coaster for a new theme park. Because this design is in the initial stages, you have been asked to create a track for the ride. Your coaster should have at least two peaks and two valleys, and launch from an initial height of 75 meters. Each peak and valley should represent a vertical change of at least 20 meters. In your design, you should plan for a mass between 400 and 600 kilograms. Once you have designed the track, you have been asked to calculate the kinetic energy, potential energy, momentum, and work done by the cart at various points throughout the track. Unless otherwise stated, you can ignore the effects of friction. Following your calculations, you have been asked to describe the energy transfers detailed by these equations. Directions To complete this roller coaster design report, complete the following: Create a diagram of a roller coaster track containing at least two peaks and two…

You’re testing a system that involves a fan, water pump, and compressor. The components are turned ON in sequence and sensor readings are taken, as per a written protocol that you’re following. The system is running as expected after the fan and water pump are turned ON. However, when you turn ON the compressor, it runs for about thirty seconds then stops, consistently. Swapping out the compressor for a different one seems to solve the problem. What could have been the issue with the bad compressor?

As an engineer responsible for monitoring works in the area of ​​mechanical systems, you must evaluate the following situation: a large client in the retail area has a refrigeration system where it stores some chilled or frozen products to be sold on the sales floor.Recently, the customer's maintenance department has been questioning the system's performance and requested an evaluation of the system's behavior. You went to the location and requested some information from the maintenance manager about the system, who provided the following data: - The system operates with R-134a refrigerant;- The refrigerated environment is maintained at 0°C and the external environment at 26°C;- The refrigerant flow rate in the system is 0.08 kg/s; In addition to the data provided, you carried out some tests and measured the temperature of the refrigerant fluid at some specific points in the system, such as the compressor inlet and condenser outlet, finding values ​​of 0°C and 26°C respectively.…

As an engineer responsible for monitoring works in the area of ​​mechanical systems, you must evaluate the following situation: a large client in the retail area has a refrigeration system where it stores some chilled or frozen products to be sold on the sales floor.Recently, the customer's maintenance department has been questioning the system's performance and requested an evaluation of the system's behavior. You went to the location and requested some information from the maintenance manager about the system, who provided the following data: - The system operates with R-134a refrigerant;- The refrigerated environment is maintained at 0°C and the external environment at 26°C;- The refrigerant flow rate in the system is 0.08 kg/s; In addition to the data provided, you carried out some tests and measured the temperature of the refrigerant fluid at some specific points in the system, such as the compressor inlet and condenser outlet, finding values ​​of 0°C and 26°C respectively.…

What would be the analysis of the given table or graph?

If an airplane is made up of many parts, what characteristics would you attribute to the system as a whole? Describe the reasons behind this.   "Please go over the engineering design in detail."

Please help and show work.

Could you please explain where and what is tight side and also how to find 5-9

ECO 5. AUTOMOTIVE. The power an engine produces is called horsepower. In mathematical terms, one horsepower is the power needed to move 550 pounds one foot in one second, or the power needed to move 33,000 pounds one foot in one minute. Power, in physics, is defined simply as the rate of doing work. The formula below gives the horsepower at 5,252 radians per second. https://philkotse.com/toyota-corona-ior-sale-in-baguio/1991-for-sale-in-aid7017151 625T 1313 where H is the horsepower and T is the torque a. Find the inverse of the model. b. If a taxi produces a horsepower of 200, what is the torque it generates? Solve here: